Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Want Better Milling & Firewood Knowledge?

how to: bedan

Posts

how to: bedan

#1

how to: bedan

dwfII

>Can someone tell me how to use a bedan? I have a good one...Henry Taylor...and I think I have it sharpened well and at the same angle as it was when I got it. But is the edge supposed to be at center? above? below? Is the tool held level? or at an angle? what??

I can get it to cut in almost all these configurations but not guaranteed smoothly. And it's a little scary when it starts to grab or chatter.

I looked at a website by a French feller when I got the tool but to be honest, I didn't get much out of that side.

I am using ghe bedan mostly to cut tenons for mounting my chuck but I know that it is good for more than that.

Thanks...

DW

In the High Desert of Central Oregon

Re: how to: bedan

#2

Re: how to: bedan

adrien

>http://www.lavieenbois.com/tournage/frame_tour_eng.htm

Pascal Oudet very skilled, this is his english site

Re: how to: bedan

#3

Richard Allen

Re: how to: bedan

Richard Allen

>I like the Bedan for rolling beads. For that purpose I use the corner of the tool. Start with the leading corner of the tool bevel up at the top of the bead (tool about 45 degrees to the floor) and roll the tooltoward the leading edge as you raise the handle.

The flat part of the tool will is the part that will be riding the wood.

On second thought get someone to show you haw to use the tool.

The tool is easy enough to use but dificult to discrib the use.

Re: how to: bedan

#4

Re: how to: bedan

Hugh Widdup

>On April 3/06 I asked about Bedan tools and received great information

I think you have to go back 16 pages to find it but it would be worth while

Re: how to: bedan

#5

Re: how to: bedan

Pascal Oudet

>Hi DW,

sorry for my late answer. I have much work now so haven't checked in for a while.

I guess the French site is mine, as indicated by Adrien.

to answer specifically your question, there are many ways to use the bedan.

you can use it level, at center, and it will behave a little like a scraper.

but the normal way would be exactly like a gouge or skew: rub the bevel !

Now I just figure the answer to your question depends on your goal.

if you are doing spindle work, use it like a gouge, above center, bevel rubbing, to "peel" the cylinder (or cut beads).

if you are decreasing the diameter (very effective with a bedan), your tip will be following an arc.

hard to describe in words.

now if you are cross gain, turning the tenon of a bowl, with the tool parallel to bed ways, it's held like a scraper (or more precisely horizontal).

but if you are at 90degrees, it works like for spindle turning.

if you are grabing maybe you are using the tool for faceplate work with a tentatively rubbing the bevel ? that doesn't work, just as it wouldn't with a skew.

if you are more specific about your problems I can maybe better help you

Pascal

Re: how to: bedan

#6

Re: how to: bedan

dwfII

>Pascal,

Yes, I think the site was yours, but I was just getting started then and even though I bought a bedan as one of my first tools (good advertising, dumb bootmaker...not that I really have ever regretted it) much of it may have gone over my head.

This explanation you offered today makes a lot of sense and is very instructive. Not the least of which is knowing that fundamentally I am using it correctly but need to refine my "touch," so to speak.

The bit about rubbing the bevel with a bedan...scares the bejaysus out of me. I can see how it would work but one errant tilt and it would be a pretty spectacular catch, it seems to me. Of course, maybe that's the problem...I haven't had the nerve to try it rubbing the bevel yet.

Thanks for taking the time...

DW

In the High Desert of Central Oregon

Re: how to: bedan

#7

Re: how to: bedan

Gordon Seto

>Pascal,

I tried to use the bedan with the bevel down. When doing larger spindle, I have trouble rubbing the bevel and preventing the heel from the hollow ground to hit the spindle. Should I grind the heel off or lift the handle to have larger clearance?

Thanks,

Gordon

Re: how to: bedan

#8

Re: how to: bedan

Pascal

>DW, not more scary that a skew ;-).

Gordon, maybe what you're describing is the reason why JF Escoulen uses it bevel up. I have never thought about that but it makes sense.

doing the "double bevel" stuff might work also, I've never tried it on a bedan.