Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Premium Live Edge Slabs, Hand-Selected in the Berkshires. Shop Unique Hardwood Pieces.

Toolmaking question

Posts

Toolmaking question

#1

Steven Antonucci

Toolmaking question

steve antonucci

>I've made a bunch of tools in my lifetime, but I've never tried to harden O1. I just ordered a bunch of O1 from Enco, and I have the following questions:

1.) Enco O1 is probably not hardened (I cut it with a file...), right?

2.) Assuming I need to harden it, a torch with MAPP gas or is that too hot? What should I look for (red, yellow?)

3.) Quench in oil (since it's O1...), but does it matter what kind? I have transmission fluid, chainsaw bar oil, vegetable, mineral...

4.) The oil should smoke, but not ignite? Last thing I want is a flaming oil slick in my driveway.

5.) If the shank of the tool is O1, it probably makes sense to only harden the tip, and not the full length, right?

Steve

Can you tell I bought a torch last night? :-)

Re: Toolmaking question

#2

Re: Toolmaking question *LINK*

Bob Fawcett

>There is heat treating info on this site


Knifemaking site

Re: Toolmaking question

#3

Re: Toolmaking question

John Lucas

>Steve right on all your questions. When you quench it plunge it completely in the oil. This reduces the chance of fire. I use peanut oil because it's easy to dispose of and has a higher flash point however anything will work. I'm sure there is a very specific way to do it if you want the best results but at home with a MAPP gas torch we probably can't do it perfectly anyway so whatever oil you have is good.

I do only heat the first few inches and leave the tang unhardened. It's easy enough to reharden the tip once you've ground past the hardened area. Old timers used to do this on thier carbon steel tools all the time.

I treat 01 pretty much like w1 except for the quenching material. If you want specifics, when you order the drill rod ask for the hardening specs and they can send you sheet that will give you all the temperatures and procedures for a certain hardness.

Re: Toolmaking question

#4

safety

John Lucas

>I forgot to mention. I keep a fireproof lid handy for the quenching vessel, do it outside and keep the fire extinguisher handy. I've never had a fire but I'm real nervous about sticking a red hot piece of metal in oil so I take precautions just in case.

Re: Toolmaking question

#5

Re: Toolmaking question

Phil Joines Krum, Texas

>1.) Enco O1 is probably not hardened (I cut it with a file...), right?

Shouldn�t be unless you ordered it prehardened. If it cuts with a file it's soft.

2.) Assuming I need to harden it, a torch with MAPP gas or is that too hot? What should I look for (red, yellow?)

MAPP is fine up to about �� diameter. Use a magnet, when the magnet won�t stick the temps right.

Temper in the oven at 400-450 degrees for an hour. You can do it be color but it�s harder to do.

3.) Quench in oil (since it's O1...), but does it matter what kind? I have transmission fluid, chainsaw bar oil, vegetable, mineral...

A lot of people use olive oil because of it�s high ignition temp. Actually, water will work just fine. It makes it a bit more brittle but that�s removed when you temper it. You need enough to quickly cool the metal. For say, the tip of a �� hollowing tool at least a pint and if it gets hot wait for it to cool down before doing another.

4.) The oil should smoke, but not ignite? Last thing I want is a flaming oil slick in my driveway.

See #3.

5.) If the shank of the tool is O1, it probably makes sense to only harden the tip, and not the full length, right?

Yes

Re: Toolmaking question

#6

Re: Toolmaking question *LINK*

Russ Fairfield

>The article that I have here on Wood Central might be helpful.


Making Our Own Turning Tools

Re: Toolmaking question

#7

Peek in here *LINK*

Jorge Castaneda ~ Downeast Maine

>Steve,

I did post this not too long ago, hope it helps.

Jorge


http://www.woodcentral.com/cgi-bin/turning.pl?nofr