Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Portable Sawmill & Tree Service – Abingdon, VA

Building an extension for General 160

Posts

Building an extension for General 160

#1

Darrell in Oakville

Building an extension for General 160

Darrell in Oakville

>Lathe Extension for General 160.

They don't exist. I looked in the catalog and on the General website, and I asked the General rep when he was at an HFMS meeting. No such animal. I can turn about 36 inches between centres on my lathe, which is fine for chair parts, but I have a new project coming up this summer: a four-poster bed for my daughter. Now, I have seen Conover's video on turning for furniture (I think that was the one...) where the guy shows how to cut a tenon on one part and bore a mortice in the other and a bead at the junction so you can get really long turnings on a short lathe. This sounds fine until you put the drill chuck and a forstner bit in the tailstock and discover that the longest piece you can *really* turn is a LOT shorter tha 36 inches. Uh Oh.

Thus, my search for a bed extension. On Saturday afternoon, when everyone else had lit out for other places and their own fun & games, I descended into the shop and started thinking seriously about building an extension bed. I measured the ways on my lathe, drew a quick diagram, and started rummaging through the metal stock out in the garage. I had inherited some angle iron and flat stock from my FIL. Now it was time to put the stuff to use. I regressed back to Kindergarten, sitting on the floor playing with blocks. Here's what I found: some large angle iron, which would serve nicely as the top surface of the extension, some small angle iron, for the lower edge of the ways (for the tailstock to grip), and some 1/4 inch flat stock to just take up space and add mass. Back down to the shop I went, with a handful of iron bars.


The first critical dimension is how long to make the extension. Well, cutting the shortest piece of stock in half yielded two 24 inch pieces, so that was that. I took the hacksaw and started cutting. I needed two pieces of each size of stock. Here's what I ended up with:


I sandwiched the parts together, clamped them, and started drilling some 3/16 inch holes at the post drill. This stuff drills fairly easily. I use 3-in-1 oil as a cutting lube when sawing and drilling mild steel. Once the 3/16 through holes were done, I took the two upper pieces (big angle and flat bar) and drilled them out to 1/4 inch. The small angle was drilled out with a #7 bit.


The #7 is what my tap/drill chart says you start with for a 1/4-20 tap. I tapped the small angle so I would not need nuts underneath. Nuts would get in the way of the mechanism that holds the tool rest & tailstock.


The big angle needed some hefty countersinks for the 1/4-20 flat head machine screws. I chucked a countersink bit in my 12 inch brace to cut these. I stood on a step stool to get up over the brace so I cound really lean on it. Had to stop to hone the bit halfway through the job.


Then I bolted everything together. A couple scraps of 5/8 inch plywood were planed down to fit the slot between the two pieces of angle iron. Then I cut the machine screws off flush with the inside of the assembly and filed them smooth. I also filed the heads of the machine screws to ensure that nothing was sticking up to interfere with the tailstock when sliding down the bed.


Next up, some kind of bas to hold the assembled iron parts. A chunck of 2x6 was just the right width. It was also propeller shaped so I had to face joint it and square up the edges first. I locked the tool rest and tailstock onto the new bed rails to hold them in their proper location and marked out the location of the two grooves. I used my Stanley #45 combination plane to plow the grooves (notice I didn't call them dados, eh?).


I screwed the rails to the plywood strips, and then glued everything together. Lots of clamps and once again the rest base and tailstock were used to ensure that the parts were properly located. So much for Saturday. Now we wait for the glue to dry...


Sunday afternoon I started moving furniture in the shop. I had to get Kathy to help me shift the lathe (man that thing is *heavy*). I also moved the bandsaur over a wee bit. This gave me enough room to mount the extension. I drilled a couple of 1/4 inch holes to bolt a bracket onto the end of the existing lathe bed. Wow, cast iron drills so easily and smoothly. Self lubricating I guess.


I used my straight-enough-edge and an outfeed support stand to align the bed. Once everything was lined up I tightened the bolts and screws on the angle bracket. The outer end of the extension needed some support, so I took another scrap of 2X6 (the cull bin at Home Despot is a great place to buy junk like this) and a couple of pieces of angle iron and screwed everything together.


My lathe can now turn 5 feet between centres. Seems stable enough, but I have yet to try it out. The bed posts should be no problem at all with this. Now it's up the the Ultimate Arbiter of Style and Design to come up with an acceptable profile for the turnings. Those

walnut beams are getting underfoot in the shop and I want to start cutting them up...

Darrell

now all I need is some green paint, eh?

Wood Hoarder, Blade Sharpener, and Occasional Tool User

Re: Building an extension for General 160

#2

Re: Building an extension for General 160

Jim Shaver Oakville, Ont.

>Never a Dull Moment in your Shop Darrell!

I know where you can get some paint... this is a good project...I was going to say to segment the posts, but it looks like you have a process outlined that will work for you. Great post on getting ready to make some posts!

take care,

Jim

Re: Building an extension for General 160

#3

Re: Been there, did this..........

Jamie Donaldson

>...several years ago. I moved my 160 tail to tail with my Stubby and bolted them together with a gusset plate. This gave me the 68" I needed for walnut bed posts turned for a local furniture maker. Well done, and now you have a really long bed lathe!

Re: Building an extension for General 160

#4

Darrell in Oakville

Re: Building an extension for General 160

Darrell in Oakville

>Hi Jim,

I will be segmenting my posts. Problem was that I could only get 33 inches or so between the headstock and the tailstock when I have a forstner bit and drill chuck in there. And none of the designs Kathy has sketched up so far lend themselves to such short segments. Her designs tend towards 40 inches for the segments. So I only need six or seven inches of the extension. But it's there if I ever need it ;^)

Darrell

Wood Hoarder, Blade Sharpener, and Occasional Tool User

Re: Building an extension for General 160

#5

Re: Building an extension for General 160

Mike Brazeau

>Nice work Darrell. Should have you around when I still had my old bowl lathe and wanted to do a bed extension. I think I would still be working with the designer to add a bead somewhere so that you could hide another joint in the posts. One of our newer members at the GHWG completed a four poster at the end of last year.

Mike

Re: Building an extension for General 160

#6

Re: Building an extension for General 160

Bob Fawcett

>Great project and write up.

I have a 4 poster in the works as well. The wife likes the Stickley posts here.

http://stickley.com/gallery/details.cfm?id=1566&c=29&cat1=11&view=all&view=complex

Not sure I am up to that challenge, so the posts may look more like this.

http://www.shopsmith.com/ownersite/proj_articles/fourposterbed/images/90120-6.jpg

I have one post lower section I turned as practice and to check how it fits the mattress. Most newer mattresses are much taller than they used to be. Ours is 15" and thats must the mattress. Add the box spring and you're close to 24". I lengthened the post and put all the extra in the square section to make it look right.


img

Re: Building an extension for General 160

#7

Re: Building an extension for General 160

hcbph

>Very impressive job. One thing that may or may not work for someone. Jet, PM & GI for 3, have bed extensions. Jet has 2, 18" and 57" so there's options out there. Any chance one of these could adapt to your lathe?

The 18" takes my Jet out to 60"

Paul

Re: Building an extension for General 160

#8

Re: Building an extension for General 160

Barry Irby

>Darrell, I like it. I did a similar thing for my lathe, but just long enough for the tail stock to sit on and tip out of the way.

May I make a hopefully constructive criticism? I don't do a lot of spindle turning, but I see a "weak link" in your set up. The piece of angle you used to attach the extension to the lathe is much too light. When you put a big blank in the lathe and crack the tail stock, that piece will be in tension and it will bend and stretch. There is also very little maintaining the alignment of the the extension. If you blank begins to wobble, the tail stock will be free to move front to rear. The wood in the joint at this point will be soft and will deform, allowing the screws to move.

An easy "fix" would be to make a piece of metal that lays on the ways and bolts into the bed on both side the way the tail stock or banjo does. Sort of a tee shaped strap with a bolt and big plate under the ways at each end. Unfortunately, that would prevent moving the banjo back and forth.

To get much service out of this you need a much stronger metal to metal connection. Its dangerous the way it is, speaking as one who caught a blank with his forehead. ($1200 worth of stitches makes a stronger connection look cheap)

Re: Building an extension for General 160

#9

Re: Building an extension for General 160

RobinCorell

>Another way to skin this proverbial cat is to drill the holes on a drill press. by doing this you can use a drive spur in one and a live center in the other and actually you gain a couple of inches in turnable length. Then instead of turning a tenon on one segment, join the parts with a loose tennon. By doing this I can get a 38" spindle on my old delta which normaly has 34" between centers. I do have to hang the tailstock off the end by about a 1/2" and almost remove the tailstock to mount the spindle. Another advantage of this method is that the centers are "captured" by the blank. the only way it is comming off unintended is if it splits.

Robin