Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

ADVERTISE HERE - FREE TRIAL

Drawknife as a lathe tool

Posts

Drawknife as a lathe tool

#1

Drawknife as a lathe tool

Curtis TX

>NO I didn't apply a drawknife to a spinning piece of wood.

I have starting learning to turn natural edge bowls. My first attempt would spin horribly in the spur drive. The drive would just sink into the bark/sap wood with out much holding power. I had an ah ha moment when pondering how to eliminate the problem. I took my second bowl blank and clamped it in my vise and used my drawknife to take out a section of bark and sap wood. The spur drive held great!

Just thought I'd share another use of hand tools in the power tool world.

Curtis

Re: Drawknife as a lathe tool

#2

Re: Drawknife as a lathe tool

Jim

>Good solution Curt.

There are several ways that I've seen to solve that problem. Some turners use a forstner bit to get a flat spot in solid wood. Others just use the chainsaw as they're prepping the blank. Still others use a large drive centers with large (wide) spurs, and crank the tailstock down to tighten it into the wood.

I like your solution just as well, as long as you it doesn't mess up the bark for a natural edge bowl. Thanks for sharing.

Re: Drawknife as a lathe tool

#3

Re: Drawknife as a lathe tool

Gil Jones on Lake Seminole GA.

>I use a 1 1/4� Forstner bit to make a flat spot.

Never thought of saving it off with my drawknife,

but know I will consider it. Thanks

Re: Drawknife as a lathe tool

#4

Re: Drawknife as a lathe tool

Barry Irby

>

Re: Drawknife as a lathe tool

#5

Re: Drawknife as a lathe tool

Barry Irby

>I have used the chain saw to flatten a spot and remove the bark and I also use a forstner bit to create a "socket" the same size as my drive spur. In some ways I like the socket. Very secure on unbalanced pieces, it might spin, but it generally will not allow the blank to fly off the lathe. A disadvantage is that if you like to move the mounting spot around to balance up the wings or whatever, you might end up with a number of sockets. You have to be careful to not put one in some critical location and have it show up in the finished piece.

Another thing that works well is to mount the piece and then lock the shaft on the lathe and rock the piece back and forth while tightening the tail stock. Sort of "Scrooching" the drive center deep into the blank. Works well on green wood.

If the only tool you own is a hammer, all your problems start to look like nails. I don't own a draw knife.

Re: Drawknife as a lathe tool

#6

Re: I use a 3/4 size cleaver,....

Jamie Donaldson

>..and on a recent demo flying trip my check baggage was x-rayed, and they had serious questions about what was I going to use it for??!!

Re: Drawknife as a lathe tool

#7

Re: Drawknife as a lathe tool

john lucas

>Curtis I have actually turned with a drawknife. It's part of my skew demo. I like your thoughts on cleaning the bark off. I usually just chisel a big square although I'm thinking about making a drive center that has 4 1/4" spikes. This should grab through the bark very solidly. What do you all think?

Re: Drawknife as a lathe tool

#8

Re: Drawknife as a lathe tool

Jim Underwood

>Actually I think I've seen that in one of my books John. I'd have to peruse them to find it, but I think it would work well.

Re: Drawknife as a lathe tool

#9

I use a broad hatchet

Jorge Castaneda ~ Downeast Maine

>and in a pinch you can turn with it too...

Re: Drawknife as a lathe tool

#10

Re: Drawknife as a lathe tool *LINK*

Bob Fawcett

>After seeing this at the "gathering" I ordered one. I think it would work for this, although I haven't tried it yet.


Chuck mounted large spur

Re: Drawknife as a lathe tool

#11

large drive centers.

john lucas

>I've looked at the ones that bestwood tools sells and they sure are nice. I happen to have some 1 1/4 x8 nuts on hand which is why I was thinking about making my own.

Re: Drawknife as a lathe tool

#12

Re: large drive centers.

Bob Fawcett

>I bought some nuts from Mcmaster Carr. I put one on the spindle the other day and it didn't run true, I could see the end away from the spindle wobble. Well, I thought, you just need a washer so it screws up flush to the flat on the spindle where the chuck seats. Put on a washer, and no change. Ok, I have five in the pack, this is the bad one and the others should be alright. Nope. All of them ran with wobble. Maybe I got a bad batch, but check the nuts you have before you spend a lot of time building something.

Re: Drawknife as a lathe tool

#13

Re: large drive centers.

Barry Irby

>I have had a bunch of face plates made out of nuts and "blind" plates. A machinist in the area puts them on a matching spindle on his lathe and trues them up. Does it without being asked. He just seems to accept that nuts are nuts and not finely machined parts.

Re: Drawknife as a lathe tool

#14

Re: I have used those nuts from McMaster also.

Al Crandall (NE of Indy)

>None of them ran true. I bolted a cross slide vice on the big PM lathe and used a metal working boring bar to counterbore the inside of the threads and face off the end so it would seat true when turned around. Then I turned it around and faced off the end which would be welded to the faceplate stock. Some of the nuts were a lot worse than others before truing. Still worth the effort I think.