Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Precision you can feel — woodworking perfected with Lee Valley

Lathe woes and plea for help

Posts

Lathe woes and plea for help

#1

Lathe woes and plea for help

John Veerkamp

>I have a Delta 46-745 Lathe purchased in Dec 02. Warrenty is 2 years. The inverter/speed control just died on me. There is a diode on the second board where one contact is loose and shows signs of sparking where it was attached. Delta no longer sells/has this speed controller. Does anyone out there have any suggestions about getting an equivalent replacement for this control unit? Possibly where I can get this repaired?

The motor specs are 1 1/2 hp, 230 volt, 3 phase, 1725 RPM.

Thanks in advance.

Latheless and desperate

John

Re: Lathe woes and plea for help

#2

Re: Lathe woes and plea for help

John Lucas

>John That really surprises me. Delta has always been really good about supplying and carrying parts, even for older machines. Possibly you can find the brand of the controller and call that company. I'm sure Delta didn't make the controller. If all else fails you may be able to buy another controller from www.dealerselectric.com

Re: Lathe woes and plea for help

#3

Re: Lathe woes and plea for help

RevDoug

>Since you've been able to locate a bad diode, could you not remove the diode in question, get a replacement, and solder it in yourself? If by chance the diode in question isn't the only issue, you won't be out but a trip to Radio Shack and a buck or two for the new diode. If you go straight to replacement, you're going to be out a couple of hundred or more.

Turn 'em round,

Re: Lathe woes and plea for help

#4

Re: Lathe woes and plea for help

John Lucas

>If it was me I would give that a try but in reality something else probably caused the diode to blow. Still it might run for a while.

Re: Lathe woes and plea for help

#5

If you need to replace the drive *LINK*

Brian Simmons, Heflin, AL

>This is the drive (link below)I have on my Schauer Speed lathe that I use for turning the big stuff. In single phase input it is only rated for 1HP though (I paid $110 2 years ago). My previous drive was a Westinghouse-Teco vfd that lasted 9 months and they would not warrant the repair because they claimed it was a spike even though I powered it down at night and it was fried the next day when I powered it back up (no chance of a lightning spike with the power disconnected!). If you buy one of these drives, email me and I can tell you more about the hook-up like making sure you install the reset button, etc. The 1HP has not been an issue for me mainly because my lathe has a massive 12" metal lathe chuck. Any way if you need more info you can email me.


Hitachi 1 or 3 phase drive

Re: Lathe woes and plea for help

#6

Re: Lathe woes and plea for help

Eddie Pacheco, San Jose, Ca.

>Radio Shack may not have a direct replacement diode so have a look at this wedsite http://www.nteinc.com/ to find a crossover part w/specs. and then you can shop around. Are you able to check the diode with an Ohmmeter (unit unplugged) to see if it has continuity in one direction only? If bad it will most likely not have any continuity in either direction.

Good luck.

Re: Lathe woes and plea for help

#7

Re: Lathe woes and plea for help

Fog Tanner

>I have the same lathe also bought around the same time. It is a Baldor controller and a Marathon motor. You can find the same one on the Baldor web site. It does not have the same face plate, as that was special for Delta, but you already have the face plate from your current one. You might check their site for repair work or a new one.

I understand the new delta lathes have a different controller made in China with their name on it. This should work in place of the one you have, but I would look at the Baldor site first.

I found that you need to keep the controller vacumed out or dust will build up and cause the controller to "fault". I suspect it is shorting across the lands.

Re: Lathe woes and plea for help

#8

Re: Lathe woes and plea for help

Kevin Mac Luskie

>I haven't had any problems with mine yet fortunately, but good to note the vacumming/blowing out the controller as regular preventative maintenance. Good Tip. Thanks!

Re: Lathe woes and plea for help

#9

Re: Lathe woes and plea for help

Wilford Bickel

>John,

Make sure you talk to a tech at Delta not just the girls in Customer Service. I just went through this with a 5 month old X5 46-755X that had a crontroller fail under warranty. The CS girls kept telling me I had a 46-765 and sent me the wrong controller. My wife is much better at dealing with these matters and called back this morning. The CS girl got short with her so she demanded to talk direct with tech. Tech called her back and had to overide the computer to locate the controller I needed - he is shipping it out! It appears some problems still showing up with conversion to Black & Decker ownership. You may need a tech to overide the system to get part you need and according to LOML will have to "insist" on speaking direct to tech who has to call you back.

Re: Lathe woes and plea for help

#10

Re: Lathe woes and plea for help

Bill Hale / The Wood Spinner

>John

Delta had some problems with this controller and I think that is why they changed. Some people have pushed hard enough and Delta has provided a new controller at no charge.

I would sure go after them and don't bother with the cust service people. Go up the ladder to the customer service manager or the sales manager, higher if need.

Good turning and be safe

Bill in Dolores,CO

Re: Lathe woes and plea for help

#11

Is this any help?

Bob Entwisle in NJ

>John

Have you been able to determine if the diode has failed? Or is the problem simply a cold solder joint that has finally failed on the PC Board? There is a pretty common problem on PC boards that are wave soldered and contain physically large components, (connector pins, large diodes, etc) which �sink� the heat from the wave solder process, so the component lead does not get hot enough during the soldering process and thus you end up with a 'cold' solder joint, which may work for a while, even years, but eventually fails. You may be able to repair the board by cleaning up the area around the arcing and re-soldering the joint.