Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

This is the most versatile work station you will ever use

Electric chainsaw sharpening

Posts

Electric chainsaw sharpening

#1

Electric chainsaw sharpening

Dawn Adams

>I just purchased the Harbor Freight electric chainsaw sharpener since it was on such a great sale this week. Figured - why not - it can't be that hard to sharpen the chain. I got it set up fine (I think) and proceeded to sharpen the chain. However, when I went to use the chainsaw, I got wood dust when it cut, not good wood shavings. Where did I go wrong. Any suggestions or thoughts on this would be much appreciated. Thank you in advance.

Re: Electric chainsaw sharpening

#2

Re: Electric chainsaw sharpening

Gary Evans Tallassee, TN

>Hi Dawn,

I'm going to guess that this chain is well used and has been sharpened before. If so, the rakers may be a little high in relation to the top of the teeth. You can find out by laying a straight edge from the tip of one tooth to the next and checking the clearance over the raker. I don't know what the correct measurement should be offhand, but I can look it up if no one else has that info.

By the way, don't listen to those who suggest that the electric sharpener is not a good method for sharpening.

I've been using one for years and no way would I go back to files. I've heated with wood for more than 25 years, and now make my living from cutting up wood, so I've earned my stripes in the sharpening wars. 8^]

Gary Evans

Talasi Hardwoods

Re: Electric chainsaw sharpening

#3

Re: Electric chainsaw sharpening

Bill Crommett

>I don't measure my rakers, I just grind them down to where I think the power head has all it can take .

Re: Electric chainsaw sharpening

#4

Re: Electric chainsaw sharpening

Gary Evans Tallassee, TN

>Me too, Bill,

That's why I don't have the clearance memorized. I usually sharpen a new chain two or three times and then start knocking the rakers down a little every subsequent time that I sharpen.

Gary

Re: Electric chainsaw sharpening

#5

Re: Electric chainsaw sharpening

JKJ in East TN

>>>I don't know what the correct measurement should be offhand...

You can buy an inexpensive gauge at chainsaw dealers: lay the slot over a raker and you can feel if it is too high.

Re: Electric chainsaw sharpening

#6

Re: Rakers

Mark Mandell - Gone Round In Jersey

>.025 to.030" max

Re: Electric chainsaw sharpening

#7

Some important things

TDaniel

>The start of the cut is made by the corner of the tooth, then the wood is peeled by the top edge of the tooth. First, to sharpen a chain you have to know what you want the final tooth shape to be, no matter what you use to sharpen it with. Second, you must sharpen until there are no "dull" spots on the corners of the teeth. If you have hit rocks or dirt you have to take a lot of metal off to get back to an area of the tooth that was not affected by the hitting of dirt. A properly sharpened tooth will have a "C" shape when viewed from the side. If sharpening with a file be aware that lowering the handle just a few degrees will eliminate the "C" shape completely. Many people push down on the file essentially sharpening the gullet and not the tooth. As I sharpen a chain I start by making a couple of strokes with downward pressure, then a couple of strokes straight back, (9o'clock), then a final couple of strokes applying pressure toward 10 o'clock, keeping the handle level or slightly above. The newer chains have a line near the rear of each tooth to help you maintain your angles. Tip: get a Husky stump vise to hold your bar while you sharpen; they make life much easier.

Re: Electric chainsaw sharpening

#8

Re: Electric chainsaw sharpening

Dawn Adams

>Thanks for all the information. I think the problem is with the raker height. The chain has been sharpened before at the shop and I have been filing it to touch it up. Then when I sharpened it with the electric sharpener I think I took a little too much off. With all this, the teeth are probably too low for the original raker height. Now I need to find the proper way to file down the rakers. This learning will never end - but it is fun!