Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

This $39 jig will make you a WOODWORKING GOD!

Chainsaw woes?

Posts

Chainsaw woes?

#1

Keith Tompkins

Chainsaw woes?

Keith Tompkins

>Does your chainsaw stumble, stall, and hesitate, and bog when you pull the trigger? Even with fresh fuel, new plug and clean air filter? Try this: Pull the carburetor off, and remove the fuel inlet side....easier than it sounds. Using carb cleaner or a similar solvent, blow out the fine-mesh screen in the body of the carb. reassemble and start. You will be amazed at the difference!

Don't know how to set the carburetor? Try this....start as usual, and let if fully warm up.(check your manual for carb screw ID) If it won't idle, or idles very low, turn the idle screw IN (clockwise) until it will idle on its own. the low speed mixture jet can now be adjusted....working in small steps, turn the low speed mixture screw in. If it stalls or begins to idle even lower, begin to turn it out (counterclockwise) slowly. the idle speed should begin to pick up. You may now have to turn the idle speed screw back out to reduce idle speed....the goal is to reach a balance..turn the screw in til the saw slows, then out until it runs rough, then set in between the two. Now you can set the high speed mixture...Do this at high rpm, and check performance while cutting a piece of wood. if it's turned in too far, the saw will lack power and will run too hot (lean). too far out, and it will smoke, and lack power as well. Again, find a balance between the two.

When finished, the saw should idle smoothly, and the chain should not move. Pulling the trigger should give instant response, and the saw should have good power, rev cleanly, and should not visably smoke.

If you totally screw it up, turn both high and low speed mixture screws in lightly until they stop. Do not force! then, back each out 1 1/2 turns each. That will put you in the ballpark.

Re: Chainsaw woes?

#2

whoa!

TDaniel

>Sorry Keith but I would not encourage anyone to set the high speed carb setting unless they thoroughly understand what they are doing. Setting this too lean will give the saw plenty of power but will burn the piston in short order. I will not give instructions for this setting because I know someone would adjust it too lean and would blame me. No harm will be done by setting the low speed needle (idle) but know what you are doing before adjusting the high speed needle.

TD

Re: Chainsaw woes?

#3

And don't forget to check ...

Brian Hahn in SW Wisconsin

>And don't forget to check the spark arrestor screen on the exhaust port. A clogged screen can really cause a saw to bog down under load. I've found the easiest way to clean the screen is to remove it and burn the gunk off with a propane torch.

Re: Chainsaw woes?

#4

Keith Tompkins

Re: whoa!

Keith Tompkins

>You raise a good point, TD, some people are not mechanically inclined. Most owners manuals describe how to adjust the mixture, but if in doubt, consult the dealer or someone knowledgeable.

A truly lean saw will be low on power, since the air/fuel ratio is off. It will rev like mad, but won't pull in a cut. You are correct about engine damage: a lean mixture runs hot, and will ruin a piston in short order.

A good way to prolong engine life...when your saw begins to run out of gas, shut it off immediately, don't keep cutting. remember, no gas....no lubrication.

Re: Chainsaw woes?

#5

Re: whoa!

DaveZ

>I agree and will add that quite a few new saws are now coming with a rev limiter in the coil. The high speed on these saws really needs to be set with a tach. Bad high speed setting= lean= meltdown.

Re: Chainsaw woes?

#6

Re: whoa!

john lucas

>New technology and new tolerances I guess. I used to tune my motorcycle the way Kieth said and ran a bunch of races running that sucker up to 11,000 rpm. She just purred and went on her way. Finally died when the auto oil injection failed. You could actually hear when it got to lean so I would back off the jet just a hair.

Re: Chainsaw woes?

#7

Re: Chainsaw woes?

Fog Tanner

>Thanks Keith for the info. I am going through those issues with my Stihl now. It has been "adjusted" by the dealer three times and with the same results as you described. I was "encouraged" by Stihl to take it back to the dealer to get it fixed. Last time I'm doing that. I am headed out now to pull the carb off.

In talking with Stihl, I found that the EPA has mandated mixture settings which are on the border of lean (in hot weather probably going lean). The saw would actually make more power if it were richened up a little, but they have stops to keep you from doing that. When I pull the carb off to check that screen, mine are comming off. The Stihl only turns 14,000, so setting the high end it not a big deal( I'm used to setting engines which are turning 24,500 at idle). Like you pointed out, do it with the engine warm. These little engines don't need to be run on the lean side, you really don't get anymore useable power, but you cut the life of the engine way down.

One thing that the factory and EPA doesn't tell you, is with the borderline lean settings the needle setting changes with the weather. On hot days, it can go lean. On the other two cycles I work with, we have to set the needle each run on the same day as it warms up. No such thing as running the same setting all day long. Same with your saw, you're not going to have the same mixture setting all year long so you are best off learning to set it yourself.

Re: Chainsaw woes?

#8

Re: whoa!

Fog Tanner

>When I first started racing high performace R/C planes, the engines "idled" at 22,500 and we set them with a tack. In flight they would turn 26,000-27,000. Most of the time that worked OK, bring it up to peak and back it down 1,100. But, after the last time I fried a piston/liner using the tack I went to setting it by "ear". Over the years the engines got more powerful and the "idle" went to 24,500 (anything less and you took a hammer to it) and 28,000-29,000 in flight. I never lost one of those engines by setting it too lean, as I only used the tack to check what the prop was doing before the run and not setting the needle.

And you are right, you can hear the engine starting to go lean even at the 11,000-29,000 range.