Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Nearly 100 Exotic Wood Species, Direct-Imported Since 1972. Shop Slabs & Turning Stock.

bowl gouge grinding instructions for Al

Posts

bowl gouge grinding instructions for Al

#1

bowl gouge grinding instructions for Al

TDaniel

>The first thing to remember when setting up a grinding jig is that the jig alone will not give you the desired profile, no matter how it is adjusted. The jig will give you a starting (nose) angle and an ending angle (side). The jig will help blend these two together. Notice I said the jig will help, not do it for you. Since there are no stops on the jigs metal will be removed as long as you hold the tool to the grinding wheel and if metal is being removed then the profile is changing. Keeping these things in mind put a tool into the jig and allow 2 1/8" to extend out, (make a gage so you can always return to this setting), set the nose angle or side angle. ( I start with the nose angle but I think the instructions advise doing the side first.) After setting one move the tool and set the other, then go back and check the first; each adjustment will affect the other. Now before grinding you must have in mind what you want the finished tool to look like. The grinding requires a lot of hand/eye coordination. I like to start a new gouge by turning it upside down and shaping the end like I want it. Just put the flute against the flat rest of the grinder and put a convex shape on the end of the tool and carry that shape back about the same distance as the diameter of the tool shaft. Then return the tool to the jig and grind until the cutting edge reaches the flute all the way around; you'll have to readjust the tool in the jig using the gage block a couple of times as you sharpen the tool the first time because removing a lot of metal on the end will change the amount of tool extending beyond the jig. Once you have ground the edge until it meets the flute you have to look for high spots where the tool shape isn't like you want it and grind the high areas off. You cannot put any metal back on so if you see a low spot you have to leave it be and grind the other part down to the low area. It is all hand/eye cordination. Look at the "Grinds" library and strive for the angles and profiles pictured. I would start with a side grind about the same length as the diameter of the tool shaft and use that for a while. Later you might want to play with the length of the side grind but get used to the tool first. Be aware that some flute shapes are harder to sharpen than others. I like the shape of Sorby and One-way better than others. Also be aware that a very small change in the distance to the wheel or the amount of tool extending from the jig will make a BIG difference in the profile.

Re: bowl gouge grinding instructions for Al

#2

Re: bowl gouge grinding instructions for Al

Carole Valentine

>TD, good explanation. I was thinking last night when Al asked me to take a pic of my Varigrind settings that my seetings would not do him much good because of all the variables involved. For instance my gouge extends 1 3/4" from the jig, not 2 1/8". The distance the V arm extends is different for all of my gouges, even though they have the same grind, because they are all different lengths. That distance will also change as my grinding wheel wears. My gouges may have different flute profiles than his as well. As you said, the jig is simply an aid. It's primary benefit is to assist one in smoothly rolling the tool from side to side without raising or lowering the handle (which is what causes multi-facets when trying to freehand grind) and to make repeatability a little easier, not do it for you.

Re: bowl gouge grinding instructions for Al

#3

Re: bowl gouge grinding instructions for Al

George Van in WI

>�That distance will also change as my grinding wheel wears.�

Carol, I have a story stick for each of my gouges that rests in the V, on the wheel guard (slow speed Delta) and touches the wheel. As my wheel wears the distance and therefore the bevel angle remains the same. Prior to doing this the bevel would get more blunt as the wheel got smaller and the gouge tipped forward. You may want to give this a try to see if it benefits you also. George

Re: bowl gouge grinding instructions for Al

#4

Story Stick?

Jennifer@Indy.USA

>Hi George,

Could you describe the story stick? Or even better a picture? You've got my interest with this. I've used story sticks for furniture building, but never for reference with my turning tool grinding.

Thanks!

Jennifer

Re: bowl gouge grinding instructions for Al

#5

Re: Story Stick?

Bob Fawcett

>Jennifer,

TD had one for his setup at the gathering. Just a small stick that is the same length as the distance from pocket to wheel. If you have your setup for a gouge, cut a piece of 1/4" dowel or similar that just fits from pocket to front of wheel.

<-----------(

Pocket^ ^stick ^front of wheel, nearest part.

Re: bowl gouge grinding instructions for Al

#6

Re: bowl gouge grinding instructions for Al

Bob Fawcett

>Oneway has videos on their site for the varigrind jig.

They now have a version for slower internet connections also. Helps to be able to see it. Read Terry's instructions and follow along with the video.

http://oneway.ca/multi-media/wolverine_videos.htm

Re: bowl gouge grinding instructions for Al

#7

Re: bowl gouge grinding instructions for Al

Ed Moore

>The geometry of the Varigrind jig in a Wolverine set-up is quite simple. There are two points that determine an axis of rotation for the jig with the tool in place. Those two points are where the tool meets the wheel and where the jig pivots in the Wolverine. The only other thing that matters is the angle of the tool relative to the line determined by the two points. Whether you extend the tool 2 1/8" or 1 3/4" doesn't matter except that you want to be consistent and use the same distance all the time. The bottom line is that the tool and jig will rotate about the axis of rotation determined by those points and with the attitude of the tool affected by the angle of the jig.

The undetermined variable in all this is the user. The pressure applied and the amount of grinding done may drastically affect the shape of the tool tip when you are done. It may be nicely rounded or narrow and pointy, and that results from a light touch and a heavy hand respectively.

To make a story stick you need three points. Two of these points are on the wheel and the third is at the pivot point in the Wolverine. Effectively it looks like a hand shaped like the letter "C" (with the thumb pulled down towards the elbow)and the elbow, but much smaller. If you put the "elbow" point in the Wolverine and slide the Wolverine until the other two points are touching the wheel then you will have duplicated the setting.

Ed

Re: bowl gouge grinding instructions for Al

#8

Re: Story Stick?

Russell L. Babbitt Jr.

>This is one of my "story sticks". The first number gives my desire angle and the next number is the notch setting on the Wolverine. Most all of my spindle gouges are ground to the same angle. All of my long grind bowl gouges are also set to the same angle. I have a seperate stick for the bowl gouges. For my bowl gouges I use either the Ellsworth jig or the Packard jig instead of the Wolverine vari-grind. The V shape block of wood in the picture is an adapter I use when using the Ellsworth or Packard jig to get the dimensions closer to Ellsworths suggestions. The black dots are imbedded magnets that help hold it in place. A bit of overkill that kinda works.


img

Re: bowl gouge grinding instructions for Al

#9

Re: Story Stick?

George Van in WI

>Jennifer, like the others my stick is a simple jig. I use a flat stick. When I first had a round dowel I had slight variations in the grid depending on where my old eyes said the center of the wheel was when I rested the radius of the dowel on the wheel. The flat stick must be straight or a gap will appear on either side to tell me it is slightly canted and therefore the distance is different than I want. The stick must also rest on the wheel guard for repeatability.


img

Re: bowl gouge grinding instructions for Al

#10

Re: Story Stick?

George Van in WI

>Side view against guard.


img

Re: bowl gouge grinding instructions for Al

#11

Re: Story Stick?

Russell L. Babbitt Jr.

>George, I like your flat stick. Easier to make, easier to use.

Re: bowl gouge grinding instructions for Al

#12

Re: Story Stick?

adrien

>i don't understand the use of a story stick to get the appropriate angle: if one has a longer or shorter tool, then the angle will either be different or the tool won't even be touching the wheel.

Do you have a different story stick for EACH tool?

Re: bowl gouge grinding instructions for Al

#13

Re: Story Stick?

George Van in WI

>Adrien, I do have a different stick for different distances depending on the tool and the grind angle, not whether the tool is longer or shorter because when I use the Vari grind I have all my tools protruding the same distance. In my case 1 ��, others use different settings for their grind and tool flute. The distance is the same for some of my tools, all of my spindle and fingernail bowl gouges, others require a specific stick. The stick is easy to make, cost nothing, and much more accurate than a bunch of marks on the V pocket slide arm. When I have the arm set and am satisfied with the grind profile I make the stick before changing the V arm.

This system will not work if you are putting the tool handle in the V pocket because overall tool lengths do vary.

Re: bowl gouge grinding instructions for Al

#14

Re: Story Stick?

George Van in WI

>Russell, I like your idea of all the information on the stick, I will add this to mine also.

Re: bowl gouge grinding instructions for Al

#15

Re: GLORY!!!

Allen Neighbors

>I surely appreciate all of you, for your comments, advice, and pictures. What a bunch of super people!!

Maybe I can make all of this work for me. I've got some pics of TD's and Carol's and I think OB's grinds, to go along with all this good info, which I have copied to MSWord, and will print out.

It's not like I'm at a standstill because of my lack of abilities though... because Old Griz won't pull against the bowl gouge anyway, unless I'm taking v-e-r-r-r-y light cuts.

I'm getting my ducks in a row, so I can place an order for a new Oneway 1640, and all the gizmos that go with it.

Thanks, all, for your help,

Allen

Getting over the Tornado that hit Childress

Re: bowl gouge grinding instructions for Al

#16

Re: Story Stick?

adrien

>Makes sense. Thanks George. I'll try it.

Re: bowl gouge grinding instructions for Al

#17

We are glad you are ok

TDaniel

>I hope you had no damage from the tornadoes. I have been scraped by two but never had a direct hit. Those things are bad news.

TD

Re: bowl gouge grinding instructions for Al

#18

Re: We are glad you are ok

Allen Neighbors

>Thanks, Terry. Our only damage was a dotted rear-end and A/C on our Travel Trailer, and a broken window in the east end of my shop. All that was followed by a sleepless night with the Fire Department. Others didn't fair so well, but we praise God that there was only one reported injury in town! That's awesome!

Thanks for posting.

Allen

Gonna turn like crazy tomorrow.

Re: bowl gouge grinding instructions for Al

#19

Re: GLORY!!!

Bill Crommett

>Al: Good that you made your way between the winds. Congrats on your determination not to lead a secondary sort of life. You will be ONE_WAY happy.

Bill

Re: bowl gouge grinding instructions for Al

#20

Excellent thread on sharpening - thanks

Mike Brazeau

>TD - This has to be one of the best that I have seen in several years of browsing. It and the AAW Sharpening DVD are really helping me to start to unravel the mysteries of grinding bowl gouges. Thanks a bunch.

Mike