Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Premium Live Edge Slabs, Hand-Selected in the Berkshires. Shop Unique Hardwood Pieces.

semented work

Posts

semented work

#1

semented work

john lucas

>I'm so psyched right now. I spent some serious time tuning my table saw and rebuilding my sliding miter jig. Before I could never consistently cut 8 segment rings. I did all my segmented work by gluing up my segments in 180 degree sections so I could true up each half before glueing the rings. It worked well, I did a lot of segmented pieces but it was painfully slow.

I have just cut 4- 36segment rings and glued them up all in one glue up with no gaps at all. I've never been able to do that before. Hopefully you'll see the results of my segmented work in the near future. I'm working on an inside out platter with segmented ring. That's what got me started on the 36 segment rings.

Re: semented work

#2

Re: semented work

georgetroy

>Are you going to join the itsy bitsy pieces crowd John? Glad to see you using those scraps. For pieces that small I use a zero clearance saw insert. If one is not available I will use masking tape to keep those little guys from pinging. I have also found a 8" super thin kerf saw blade to work quite well on the little stuff. Assuming you have a disc sander to flaten. I know you have the expertise to do everything well, looking forward to seeing you segmented projects. GT

Re: semented work

#3

Re: semented work

John Lucas

>George. I'm using an 1/8" blade because it's the best one I have. My sliding table saw jig has an 1/8" kerf so it works well as a Zero clearance insert. I did a small ring last night and ran into a problem I hadn't counted on. The wind from the saw blade was blowing the pieces back between my stop block and angle guide and made them hard to retrieve. I use a pencil with an eraser to hold the tiny pieces. I had to remember to not let go until the blade was at least 6 inches away or it blew them into the non retrieval zone. I will probably switch back to 8,12 or 16 sides for smaller ringed pieces but right now I've got it set for 5 degrees so I'm just going to keep going on this piece and my inside-out piece and then I'll switch back to a more appropriate number of sides.

It's kind of like my statement above about the long stemmed goblet. You have to make something really difficult to prove to yourself you can do it, then you need to get back in the real world and make things that are appropriate for the task. Unless you need a 36 sided ring for a certain look, make the number of segments that best fits the task at hand.

Re: semented work

#4

What could be better!

Ron in Drums PA

>What could be better!

First, you get to use your flat woodworking tools.

Then you get to build something out of wood.

And you get to turn it too!

How cool is that!

Re: semented work

#5

Re: semented work

Mark Kauder, Phenix City, AL

>COWARD (Just kidding)

I am working on a piece with 72 segments per ring - 54 1/4" rings. 72 segment 4" rings are fun!!!

Call if you need some help. I have moved to a stop block that is fixed to my TS fence, so that as I move the sled forward the stop is gone, and the cutoff piece does not get caught between blade and stop.

Mark

Re: semented work

#6

Re: semented work

John Lucas

>Mark I did some 72 segment rings for my handmirrors many years ago. I cut them by hand with a homemade miter box and a good dovetail saw. I remember I made some sort of fine tune device that I was quite proud of but now I can't remember what I did.

I would be really interested in your cut off jig. I don't remember what it looked like. You had so many interesting things in your shop.

Re: semented work

#7

Re: semented work,slight hijack

Barry Irby

>I just picked up the 2005 winter AAW Journal and read the article on segmented turning.

I was thinking of segmented turning as a way of using up scraps, but got sidetracked. There is a chart explaining the angle you use for various numbers of segments: 6=30 degrees, 8 equal 22.5 Degrees etc until 36 = 3.75 degrees. That's an error isn't it? 36 segments requires 5 degrees, right?

Second, they put emphasis on prepping the stock. This is not a good way to use little scraps, is it? You need such accurately cut pieces it would be better to take larger strips and cut them down. Or do you use scraps?

Re: semented work

#8

Re: semented work,slight hijack

John Lucas

>Barry 36 sides is 5 degrees. I have used scraps, it just requires more work. I built a jig similar to the one that Malcom Tibbets uses for shaping the segments on the disc sander. cut them roughly to shape on the bandsaw and final shaping with the disc sander. The main difference is the thickness and length of the pieces may vary so it requires more work to true up the rings. Thickness wasn't much of a problem for me since I trued my rings up on the lathe. One surface would be flat while the other was way off, but this was easily trued on the lathe. I glued these up in pairs, and then glued the pairs togetherand then those groups toghether etc. so clamping wasn't a problem it was just slow going. This did let me check the accuracy because I would do my segments so that they could be glued together to form 90, then 180, and then 360. This let me sand out any errors as you go. Not the most accurate way to do things but it does give you good tight glue joints.

Re: semented work

#9

Re: semented work,slight hijack

Ron in Drums PA

>Dividing 180 by the number of pieces will give you your angle

180/36=5

180/4=45 (a box)

Re: semented work

#10

Re: semented work

Bob Fawcett

>Sounds like a job for a shooting board and a hand plane. This is great tool for removing wood 1/1000 at a time.

you can also add a fence for angles. It can be fine tuned with small shims.