Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Precision you can feel — woodworking perfected with Lee Valley

Intermittant Jet 1236 vibration?

Posts

Intermittant Jet 1236 vibration?

#1

Intermittant Jet 1236 vibration?

GaryG in MD

>I have a Jet 1236 and consider it to be a decent, inexpensive lathe. It's all I need until I improve my tool skills. ;-)

I've been having a problem with intermittant vibration. Let's say I have a small item mounted -- in perfect balance. I turn the lathe on and off a few times, and everything is fine. Then I turn it on again, and it vibrates. Nothing serious, I can still turn, but it's annoying -- I like to listen carefully to the cut when I turn, and this vibration is enough to make the banjo vibrate a tad and the banjo handles rattle (even though I have a rubber band around them to prevent that). It may do that a few times, and then, seemingly at random, it may come on perfectly smooth and quiet again, with absolutely nothing changed.

I'm assuming it probably has something to do with the belts, but I've never removed the cover -- it's effectively factory fresh.

Has anyone else had this problem, and what can/should I do about it?

TIA, Gary

Re: Intermittant Jet 1236 vibration?

#2

Re: Intermittant Jet 1236 vibration?

john lucas

>Gary If I remember right that lathe has a Reeves drive. The belt is probably causing the vibration. I'm not sure of the solution other than lubricating the shapt that the pulleys slide on so they move more freely. Check the condition of the belt.

You also have a revolving headstock on that lathe. Check to see that it's locked down firmly.

I don't remember how the spindle is attached to that lathe. On my Jet mini the handwheel tightens down to draw the spindle into place. If it's loose you get vibration. I don't believe your's works exactly that way but I would check all points on the spindle to see if everything is seated properly.

These are purely guesses but I hope they help. John

Re: Intermittant Jet 1236 vibration?

#3

Is It Moving?

George (Oxford, NC)

>What type of floor do you sit on? If a garage concrete that is not exactly the best for smoothness, is the lathe moving a tad so that it hits an uneven balance point between the legs and the floor?

George

Re: Intermittant Jet 1236 vibration?

#4

Re: Intermittant Jet 1236 vibration?

Bill Hale / Woodspinner

>Gary

I am not sure on the drive but if it is not a reeves check the pulleys and be sure they are locked down tight. If a pulley is loose it will cause that exact problem.

Good turning and be safe.

Bill in Casa Grande, AZ.

Re: Intermittant Jet 1236 vibration?

#5

Re: Intermittant Jet 1236 vibration?

Ken Grunke from SW WI

>Could be nothing more than a loose screw.

A buddy of mine came across a good deal on a 1236 last weekend, pre-owned but barely used. No shop space of his own, so he had to twist my arm into letting him store it in my shopspace for an almost indefinite period of time (near an outlet, of course).

There are 4 screws holding the headstock cover on. Turn the lathe on and loosen one of the screws just a bit, you will likely get a vibration like I did when I did that.

There are a few bolts and screws in various places, go all over the machine and check for tightness. Also the feet have adjustable pads, snug them up to the floor evenly.

The 1236 does have the Reeves drive, and it isn't the smoothest or quietest running either. The pulleys are open spoked, for lack of a better description--rather than being solid and smooth where the belt makes contact. Time will tell whether that causes belt wear sooner than normal pulleys or not--I'm sure that design makes the lathe a bit louder and vibration-prone.

Re: Intermittant Jet 1236 vibration?

#6

Thanks, all, for your replies

GaryG in MD

>I'll pull some screws and see what's going on in the drive. Hopefully I'll be able to post a solution for others who follow. ...Gary

Re: Intermittant Jet 1236 vibration?

#7

Brad Vietje

'Nother possibility...

Brad Vietje

>Could also be the lever handles for the tailstock and/or banjo. These are threaded in, and sometimes don't stay tight. I had to keep tightening up the tailstock lever -- CA on the threads will cure that one.

Safe Spinning,

Brad Vietje

Newbury, VT

Re: Intermittant Jet 1236 vibration?

#8

Re: 'Nother possibility...

GaryG in MD

>Thanks for the thought Brad. The vibration is very binary -- either it's there or it's not -- one time I hit the "start" button it may do it, and the next time it may not. That makes me think it has something to do with the belts. I'll look and see what's going on under the cover when I can find the time. ...GG