Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Good Hope Hardwoods - Walnut Slabs & Specialty Hardwood Lumber

My Attempt

Posts

My Attempt

#1

My Attempt

Barbara Gill

>I was taken with the home made handles Molly had for her coils and other self made tips. One was made per Graeme Priddle; it was simplicity at its finest. The other was more refined but way over priced. On the way home from the Gathering I started thinking about how I would make one using both examples. This is what I came up with.


img

Re: My Attempt

#2

Picture #2 

Barbara Gill

>


img

Re: My Attempt

#3

Size: 6 1/4" Long

Barbara Gill

>

Re: My Attempt

#4

Good Grief!

Barbara Gill, Remlik VA

>I just re-read what I wrote. I didn't mean to imply that Molly was selling them and they were over-priced. She showed us one she had bough; it was over-priced.

Re: My Attempt

#5

Re: Good Grief!

Jim Shaver Oakville, Ont.

>Hi Barbara,

I didn't read it that way, but I know we know the character of Molly well, I think it takes a special person to open up their process and show us in detail how they do things...that is what makes this community special!

It was also considerate for you to make this post to clear up what you thought was potentially information that could be misunderstood.

Take care,

Jim

Re: My Attempt

#6

Re: Good Grief!

Gil Jones on Lake Seminole GA.

>Barbara,

I did not take your post that way either, and your burning pen looks great! Now all you need is Nichrome wire and copper nails (and a powersupply/controller). Luck...

Re: My Attempt

#7

Re: My Attempt

Carole Valentine

>Looks like that will work just fine, Barb. I didn't get the nails in the mail today...hope tomorrow.

Re: My Attempt

#8

Re: My Attempt

Eddie Pacheco, San Jose, Ca.

>Hello Barbara,

Will the plastic connector that you are using for securing the tip stand up to the heat? Do the ends of the nichrome wire connect to the white terminal block? I have no experience with burners, but I have seen the plastice bodies of these connectors fail from excessive heat due to current.

Re: My Attempt

#9

Re: My Attempt

Molly Winton

>They'll eventually melt a bit, but this method was designed by Graeme to be more of a temporary pen, rather than one that will last long. I had some char build up that eventually interfered with the current and the pen failed, but Gil Jones figured it out for me and we cleaned out the build up. It works fine now.

Very cool Barb. I haven't had a chance to make up the pen you sent me, but when I have a chance I'll let you know how I like it. Thanks a bunch!

Re: My Attempt

#10

Yeah, What She Said. :-)

Barbara Gill, Remlik VA

>You are welcome Molly. I figure if the connector fails it can be carefully sawn off with a bandsaw and a new one glued in place. The handle didn't take very long to make.

I didn't complete yours because I thought you might not want the connector where I would glue it.

Re: My Attempt

#11

Thanks

Barbara Gill, Remlik VA

>

Re: My Attempt

#12

Re: Yeah, What She Said. :-)

Norm Smith in Nova Scotia

>Barb, That looks great. When everything is complete how about posting a picture with step by step instructions.

Norm

Re: My Attempt

#13

Re: Yeah, What She Said. :-)

Barbara Gill, Remlik VA

>All I did was take a 3/4" board and cut two pieces the length I wanted so when they were glued up it would be about square. I routed a channel in each side before gluing them together (that was easier than trying to drill through the thing).

Then I just put the glued up block on the lathe and turned a handle which felt comfortable,leaving the top part where the wire connection large enough to work. I held the turned handle in a clamp for safety and carefully sawed off the part of the handle that needed to be flat. I lightly sanded the cut edges and then glued the piece of Barrier Strip with CA glue.

Then just get a piece of lamp wire and run it through the handle and secure the bare wires as shown in the pic. I have not bought the piece that plugs into my burner but that piece goes on the other end. All of the how to instructions came from Molly's demo. Nothing I did was particularly original.

Re: My Attempt

#14

Re: My Attempt

Jennifer@Indy.USA

>Barbara, it looks great! Nice job.

If you have it handy...could you give us the part number to that little do-hinky from Radio Shack? Thanks!

Jen

Re: My Attempt

#15

There ya go using those technical terms again!

Molly Winton

>

Re: My Attempt

#16

Re: My Attempt

Phil Joines Krum, Texas

>I donn't know who might stock them but if you can find some of the black phenolic barrier strips they would be less suseptable to heat.

Re: My Attempt

#17

Believe It Or Not...

Barbara Gill, Remlik VA

>I kept the number. It is 274-677. The part is called a 12-Position Barrier Strip. Of course Carole and I didn't know that when we went into a Radio Shack in Greensboro. We did however know what it looked like and could describe it and the usual function to the clerk who knew as little (maybe less) than we did. Finally someone who knew something opened the bottom drawer of a big display and there it was. I used a hacksaw to separate the blocks as they are used for the handles.

Re: My Attempt

#18

McMaster-Carr has phenolic strips & nichrome wire

Craig Daymon

>Finally got McMaster-Carr page to load.

They have both phenolic barrier strips (terminal blocks) on page 700 and nichrome wire on page 3514.

Molly, McMaster lists the wires by diameter. What is the diameter of 20 gauge wire?

Thanks,

Craig