Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Urban Salvaged Hardwood Slabs, Milled In-House from Rare Trees. Shop Unique Walnut Stock.

craftsman 15" v/s lathe

Posts

craftsman 15" v/s lathe

#1

craftsman 15" v/s lathe

byron

>Anyone know anything about this lathe? I have been looking at one

that is for sale and when i turn it on it is quite noisy. I don't know

if it is the bearings or that it is normal/ This lathe is nearly new

and is priced at $400. There are several accessories that come with

it such as a chuck,8" face plate,set of chisels including 4 scorby

swan neck tools and several live centers. Is this a good deal as i

am leary of the noisy head.

Thanks, Byron

Re: craftsman 15" v/s lathe

#2

Steven Antonucci

Sold mine as fast as I could

steve antonucci

>for all of the reasons you mention. Bearings were fine, noise is normal...

I think they cost about $400 new, so I'd pass...

steve

Re: craftsman 15" v/s lathe

#3

Brad Vietje

Re: craftsman 15" v/s lathe

Brad Vietje

>Byron,

Couple of thoughts:

Craftsman lathes are not top-shelf to begin with; I can't think of a Craftsman lathe worth $ 400.00 to me.

Noise could be bad/shot bearings, but could also be other things, depending on how the speeds are changed. Does this have mechanical variable speed -- which would mean changing speed without stopping the lathe -- or a series of stepped pulleys? If the former, these Reeves drive knock-offs are pretty well known for wear around the sliding sheave hubs, causing a loose and noisy pulley. These can be replaced without a lot of heart- (or wallet)ache. It could also be minor; the shaft could be so caked with gunk (a technical term for dust and oil), that the pulley sheaves simply can't slide on the shaft to the proper position, resulting in a loose belt that makes a lot of noise.

If the speed is changed by stopping the lathe, and moving the belt from one size pulley to another, make sure its not loose, and just noisy because its allowing the belt to flop around. If it's not loose, but still noisy, stay away.

Safe spinning,

Brad Vietje

Newbury, VT

Re: craftsman 15" v/s lathe

#4

Re: craftsman 15" v/s lathe

Jerry Whitaker

>Run, Run, Run and never look back. They are bulky and ugly too.

Re: craftsman 15" v/s lathe

#5

Re: craftsman 15" v/s lathe

byron

>This lathe is about 2yr old but he never turned anything on it but

one practice piece. I don't think it is a reeves drive as the speed

is controlled by rotating a knob as a reostat. Also the tail stock

moves too much and when locked down it doesn't line up with the

head stock. You have to align it first and then lock it down. I

think i will pass on this.

Byron

Re: craftsman 15" v/s lathe

#6

Re: craftsman 15" v/s lathe

Carole Valentine

>Passing is a good move. You would be better off to put that money on a Jet Mini and accessories.

Re: craftsman 15" v/s lathe

#7

Pass

tek-Brunswick, Ohio

>Good decision!

Re: craftsman 15" v/s lathe

#8

Re: craftsman 15" v/s lathe

Ron in Drums PA

>There is a reason the name of this lathe is pronouned "crapsman"

Re: craftsman 15" v/s lathe

#9

Re: craftsman 15" v/s lathe

Bob Fawcett

>you can get a Jet mini for less than $300. Use the other $100 to start a collection of tools. I got a 6 piece Sorby set from Woodcraft for $150 on sale. I haven't seen this particular set since, but it is worth watching for. You can get other quality tools for a little less.

Re: craftsman 15" v/s lathe

#10

Re: craftsman 15" v/s lathe

Ken Grunke from SW WI

>Must be a universal DC motor the way it sounds. You are wise to look the other way, unless it's free--a friend of mine has a Craftsman lathe with integral motor in the headstock and it's been nothing but trouble.

Re: craftsman 15" v/s lathe

#11

Re: Sold mine as fast as I could

Bill Hale / Woodspinner

>Go to a local boat dealer. ANCHORS start at $ 12.00

Bill in Casa Grande,AZ.

Re: craftsman 15" v/s lathe

#12

Re: craftsman 15" v/s lathe

byron

>Ok ithink i have gotten a good response toward this lathe. I also

did not like the way the tail stock did not line up with the head

stock unless you manually did it and then locked it down. I have

been looking at the rikon when this came along so i probably go

that route. Woodcraft is going to lower the price on the jet mini

with the chuck to $265 in june. I think rikon is giving jet some

competition.

Byron