Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Exotic Hardwood, Personally Sourced Worldwide. Inspected at Origin. Shop Rare Stock.

Forceps?

Posts

Forceps?

#1

Forceps?

Carole Valentine

>Where's the best place to get fairly heavy duty 12" locking forceps for sanding inside vessels? Is curved better than straight? It would seem that it would be. No medical supply stores here so I can't look before I buy. If anyone coming to the gathering has an extra pair they want to sell, let me know!

Re: Forceps?

#2

Re: Forceps?

John Lucas

>Carole I've gotten mine from Harbour Freight or one of the discount tool shops. In fact I think I can get them from my local flea mkt. I will go look on Saturday and see. If they have them I'll pick you up a pair. I have both straight and curved and don't see much difference for most work but once in a while the curved pair really comes in handy.

Re: Forceps?

#3

Re: Forceps?

Wally Dickerman in Arizona

>Craft Supplies...page 61...$8.50. I use them often.

Wally

Re: Forceps?

#4

Re: Forceps?

Ron in Drums PA

>Do you know a Doctor or a Nurse?

I got a couple of freebes from them

Re: Forceps?

#5

Re: Forceps?

Ed Karch

>I will bring you a pair of sponge forceps. They are the best for sanding inside vessels. They are not 12" long however. What kind of critter do you know that has 12" long fingers for feeling inside?

Re: Forceps?

#6

Re: Forceps?

RussFairfield

>Be very careful with those forceps, and NEVER hold them with any of your fingers inside of the loops.

TD had a little dog that did a good sanding job on the inside of hollow forms.

You might also try the "tumbling sanding" method. Fill the form to about 1/4 full with any abrasive sand or small crushed rock. Plug the hole in the top and rotate in the lathe at a slow speed somewhere below that where the sand is held against the sides of the vessel.

Tumbling works very well for wood that is uniforn in density and hardness. It doesn't work very well if there are soft spots. It gives an interesting texture to woods with alternate hard/soft growth ring.

Re: Forceps?

#7

Re: Forceps?

Carole Valentine

>LOL! Aliens, maybe? Thanks, Ed. I would like to be able to get to the bottom of pieces, even if you can't get your finger that far. I can see it with my light, even if I can't feel it. I guess I might be a little O-C. ;)

Re: Forceps?

#8

Thanks, Wally

Carole Valentine

>

Re: Forceps?

#9

Re: Forceps?

Carole Valentine

>Did TD stuff his dog inside the form? LOL I want to try the rocks thing and see if 100 rpm is slow enough, but even if it is I doubt I would use that method often since it would tie up my lathe. Will look at TDs littel dedicated set up he has.

Re: Forceps?

#10

Re: Forceps? Mebbe so....

Allen Neighbors

>Carole, I'll check at the "good old place" here in town. They usually have several different sizes... I'll see if they have any large ones, and let you know tonight.

Allen

Re: Forceps?

#11

Re: Forceps?

Wally Dickerman in Arizona

>Russ is right, be carefull. I always bring up the tool rest to rest my hands on for better control while I'm using the forceps.

Wally

Re: Forceps?

#12

Thanks Allen

Carole Valentine

>

Re: Forceps?

#13

Re: Forceps?

Carole Valentine

>Thanks John, but wait and see what some of the folks coming to GA come up with. Looks like several may have something.

Re: Forceps?

#14

50 rpm or less

TDaniel

>