Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

REAL MILK PAINT

steb center

Posts

steb center

#1

steb center

Dennis Taylor

>looking for a upgrade to the conventional 4 prong drive, and was looking at the Steb Center by Sorby....I have been turning lately some baseball bats between centers, and think being able to remove the piece and reposition would be nice...I was thinking about the 1/2 center with a #2 MT, does anyone have experience with them...the blanks are 3" round and about 30" long, is that more than a 1/2 can handle?....also...looked at the centers for a 4 jaw chuck but wonder if that don't limit access due to the jaws being in the way...any input is appreciated...Dennis

Re: steb center

#2

JL

Re: steb center

JL

>It handles chair legs (starting at 2 1/2" x 26") quite nicely.

Re: steb center

#3

Re: steb center *LINK*

Fred Holder

>I've been using Steb Centers even before Robert Sorby started to make them. I have the 1/2" size and it is either 3/4" or 1", I'm not sure, but that is what I use for all between centers work. I have one of the live Steb Centers from Robert Sorby that I use in the tailstock. These do not make a deep center point in your work and they hold very well. I don't believe I've ever had a spindle split or jump off of the lathe using the Steb Centers.

I also use them to start medium size bowls, up to 12" in diameter between center. They hold the bowl quite well. I turn the outside between these centers or between the tail center and the chuck jaws to turn the outside and the foot to fit into the chuck.

I no longer use any other type of drive center since I purchased a Steb Center several years ago.


Fred Holder's Domain Site

Re: steb center

#4

Re: steb center

William Duffield, on the Cohansey

>I've used the 1/2" Steb center for turning a few carving mallets, finished diameters about 3", out of some very tough, seasoned hardwoods. Now that I have the choice, I never use my traditional spur center. The Steb center has many advantages, and (except for the purchase price), no disadvantages that I have found. For diameters larger than 1-1/2", I suppose a larger diameter Steb center would probably work better, because sometimes the smallest one spins while roughing the blank, and the tail stock needs to be retightened, but that has not been enough annoyance for me to buy a second one. Since most of my spindle turning is of diameters less than 1-1/2", the smallest Steb center made the most sense to me. The thing I like best about it is that, when I have to remove and then remount the stock on the center, getting the stock recentered exactly is a no-brainer.

Re: steb center

#5

Stebs rule...

Peter Teubel

>I started using Steb centers a couple years ago. I use them for all my spindle turnings. Got rid of all my 4-prong spurs.

Re: steb center

#6

I like it..well, the copies anyway

Craig Daymon

>I have one from Craft Supplies. It doesn't have the compressable center point, but has the same outer crowned rim. I also have a larger one from Penn State Industries that does have the compressable center point. (They have a smaller one as well.) I think the Steb Centers are around $65, but these were closer to $25. Gives me a little extra for wood. Of the 2 aftermarket models, I think the Penn State version is much better made.

-Craig

Re: steb center

#7

Re: steb center-try the safe driver from Oneway

Greg H. from Wisconsin

>I would recommend the Safe Driver from Oneway, less expensive and better in my opinion, but you know the saying about opinions.

Thanks

Greg

Re: steb center

#8

Re: steb center-try the safe driver from Oneway

Dick Gerard

>Like Fred Holder I have been using Steb centers a long long time, both in headstock and tailstock. Yes, they are a bit pricey. But, ask yourself this ... how much is it worth to know, absolutely know, that you will never fumble with recentering again, and, you will never need to purchase a new drive center like the Steb. The much smaller indentation from the center point is another big advantage. It enables you to slacken the tailstock just a bit, the spring loading takes over and pushes the item away from those beautifully machined and oh so sharp teeth ,,, and without shutting the power off, you can swap out for the next item. Especially useful if you are doing more than one of anything. I value my Steb centers almost as much as my 4 jaw scroll cuck. And I never loan it out. The 1/2 inch has done just fine. I turned posts as large as 6 inches square with no problems (just don't get too aggressive) .. but that applies to any turning situation, doesn't it?

Re: steb center

#9

Re: steb center

John Lucas

>I've never had a problem putting a spindle back on the lathe using a 4 prong center. I mark one of the jaws with a V file so it leaves an different mark. I can them put the spindle back on exactly as it came off. My 1/2" steb center works well for heavier spindles like chair legs but the pressure from the spring loaded point puts too much pressure on small spindles and makes them chatter.