Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Support WoodCentral when buying things you need

$$ Saving Options

Posts

$$ Saving Options

#1

$$ Saving Options

Rick Davenport

>In my short experience I have found items sold in specialty turning catalogs can sometimes be found elsewhere for lots less $$.

For example, I looked into a buying turning smock. I ended up getting a golf "wind shirt" with ribbed collar and sleeves for $25.oo at a local discount sporting goods store.

And I looked at the $10 pen insertion tools advertised in most catalogs and decided to use a bamboo chopstick instead. I just whittle off the glue buildup. I haven't had to replace the free chopstick yet.

All you experienceder folks out there:

What are some money saving ideas you have found that we could all benefit from??

Rick

"Life shouldn't be dull."

Re: $$ Saving Options

#2

Re: $$ Saving Options

RussFairfield

>A plain old wooden lead pencil also works pretty well as an insertion tool for the brass tubes, and it can be cleaned up in a pencil sharpener. Just make sure the CA is cured before sharpening.

Re: $$ Saving Options

#3

Re: $$ Saving Options

Don Tewell

>The same can be said for a lot of items. When an item says "Photographic" or "Woodturning" the price doubles or quadruples from it's original price. I think you have a very good idea. Sharing money saving tips. I am going to build a steady rest this week because I don't/can't pay full price.

Re: $$ Saving Options

#4

Re: $$ Saving Options

Ken Grunke from SW WI

>Closed-cell foam sheet for vacuum chucks, friction chucks, sanding pads:

Foamies, 9 x 12 sheets with stickum backing--about 60 cents each at walmart.

My fellow club members call me "Mr. Foamie" because I keep pushing the stuff ;)

Re: $$ Saving Options

#5

Re: $$ Saving Options

Wally Dickerman in Arizona

>Garage sales....I bought a pair of used in-line skates. Enough steady-rest wheels so that you can share with a friend. Tools at garage sales. I bought a 12-inch caliper for $1.

If you buy hardened steel to make a tool, it usually needs to be tempered to hold an edge. A metalurgist might put it in with other stuff and charge you nothing. Happened to me.

You can buy a box of paraffin for about $3 at the grocery store. The kind my mother used to use to seal canned goods. It's a lifetime supply of my method to keep my lathe bed and tool rests slick.

Wally

Re: $$ Saving Options

#6

Re: $$ Saving Options

Don Tewell

>Hate to sound dumb(er) but what are 'foamies'?

Re: $$ Saving Options

#8

JL

Re: $$ Saving Options

JL

>Old mouse pads - great for jam chucks and padding. Everyone has them

Re: $$ Saving Options

#9

Re: Foamies

Allen Neighbors

>9X12 sheets of closed cell foam with adhesive back, that is sold in WalMart Craft department. 48cents a sheet, in West Texas. :o)

Allen

Re: $$ Saving Options

#10

Re: $$ Saving Options *LINK*

Tim Grenville-Cleave

>Browse the site linked below, Gazillions of ideas and tips, you may find one or two you like.

Tim


Laymar Crafts

Re: $$ Saving Options

#11

CA and epoxy glue

Ken Grunke from SW WI

>can be had for better prices at well-stocked hobby stores. Can't quote any prices right now, but my local hobbyshop has a selection of 4 thickness grades of CA in large bottles (I think 4 oz), plus they have epoxy in larger sizes than the little tubes found most other places.

If model airplane freaks rely on the stuff, it's gotta be good.

Re: $$ Saving Options

#12

Re: $$ Saving Options

Bob Fawcett

>Made my own sharpening jigs from information found on the net and some of my own ideas. Saved $200 vs buying the Wolverine system.

Made my lathe stand out of lumber in the wood pile. Stability provided by 3 bags of concrete I left outside under a tarp too long. They are 100lb "bricks" now.

Bought a Crown bowl gouge on closeout and sharpened it to Ellsworth profile with the above jigs. Cost half the price of Ellsworth gouge. Looks nearly identical to friends true Ellsworth.

Bought P & N tools without handles from Lee Valley and made own handles. They cost less than Sorby or other good brands. The steel is just as good. You may save some shipping cost as well. I get to shape the handles the way I like them.

Cut the end off a downed tree in my yard to use as practice wood. Turned out to be spalted oak.

Re: $$ Saving Options

#13

Re: $$ Saving Options

john lucas

>Goodwill has inline skates really cheap.

Re: $$ Saving Options

#14

Re: CA and epoxy glue

john lucas

>Ken We buy CA glue in quantity directly from the dealer. The club buys it and sells it with just a tiny bit of profit. We can buy 2oz bottles for $3.50 and the club still makes money.

Re: $$ Saving Options

#15

A lot of great ideas!!!!

Rick Davenport

>

Re: $$ Saving Options

#16

Re: CA and epoxy glue *LINK*

Mark Kauder. Phenix City, AL

>we do too.

This place has a $100 purchase minimum.

Mark


http://www.e-zbond.com

Re: $$ Saving Options

#17

Re: A lot of great ideas!!!!

Don Tewell

>Rick, thanks for starting this. I've picked up a lot of ideas. I feel smarter now that I know what 'foamies' are.