Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Nearly 100 Exotic Wood Species, Direct-Imported Since 1972. Shop Slabs & Turning Stock.

Help with stencil process

Posts

Help with stencil process

#1

Help with stencil process

Dave Belser

>I'm trying to paint letters and graphics on some turnings. I've got a method that is working OK but still gives me trouble. Here is what I'm currently doing:

Apply sanding sealer or 2# cut of shellac - this prevents reduces bleed around the mask edges.

I'm using a stickon vinyl mask that I cut on a sign cutter, this is applied to the sealed wood.

Spray paint over the mask / stencil, I'm currently using a cheap can of semi-gloss or flat black which may be one of my problems.

Apply several coats of wipe on poly. After I remove the mask there is an "edge" where the black paint stops. I've chosen wipe on poly as a final finish because I need something durable and resistant to alcohol.

The final piece is buffed to a high gloss.

What I seem to be fighting the most is that I need to build up the finish over the edge of the lettering. I have to be very careful with the first coat of poly as it's easy to make the paint bleed or run. I lightly sand between coats of poly. This reduces the edge on the lettering and is supposed to help the poly coats stick together - but it's also easy to sand the letters off!

The only part of this process that I'm locked into is using a vinyl stick on mask - my hand writing is so bad that I often can't read it!

Any suggestions would be greatly appreciated.

- Dave

Re: Help with stencil process

#2

Re: Help with stencil process

Gary R

>Spray from a can gives way to much paint. To get a nice clean stencil edge, I would recommend a visit to a craftstore.

-- Try some acrylic paint, and a stencil brush. These brushes are very short bristles. Low cost stencil brushes are perfectly flat cut. I find better quality (softer) brushed are cut in a slight dome shape at the end. You need a little give to the brush - cheep ones are to rigid.

-- Place a small amount of paint on a scrap piece of wood

-- Holding brush straight, use a light pounce technique to put paint on the brush

-- On a paper towel, again using pounce, dab brush and paint to remove most of it

-- When it looks like you removed to much, you are there - only a little needed (almost dry)

-- Use the pounce technique on your stencil

Given brush is almost dry, paint transfer is very light. This will keep buildup from teh edge of the stencil.

You can spray over acrylic when you are done to preserve.

Hope that helps.

Re: Help with stencil process

#3

Re: Help with stencil process

tek-Brunswick, Ohio

>Am I reading your post right? Are you putting on the wipe on Poly before removing the mask? You are building up the area inside the mask too thick. Are you starting your spray pattern before your cutout and finishing it past your cutout? It gives a more even finish than just blasting the paint at the hole.You need to just use enough paint to get the color consistant. Lacquer usually buils up less that enamel. I'm not sure which you are using. An airbrush and airbrush colors would probably be your best bet, but if you don't own one it is an expense. You will still have a little ledge. You will have too still use your sanding between coats to blend in the edge, but not as much.

Tom

Re: Help with stencil process

#4

Re: Help with stencil process

Phil Powell

>Gary's response was excellent. However, if you still want to use spray paint, first

spray a light coat of a clear finish to seal the edge of the stencil then the paint.

Remove the stencil before the extra coats of clear poly. A very light sanding with

a wet and dry extremely fine paper used wet should knock down the raised edge.

Re: Help with stencil process

#5

Re: Help with stencil process

tek-Brunswick, Ohio

>I would be tempted to try Garys method. It may be better than my suggestions.

Re: Help with stencil process

#6

Thanks and more info

Dave Belser

>Thanks for the suggestions -

Gary - I figured I had a problem with the spray paint I'm using. Clearly I need to try to get less paint on in the first place.

Phil - Not sure what you suggesting here. Spray after applying the mask but before painting? The sanding sealer coat takes care of any bleed problems I had and it sounds like any more coats than necessary with the mask on will give me even thicker edges.

Tom - Once I've painted the mask comes off. My spray technique is pretty good I think - start the spray off the piece, hold can a good distance away and proceed with an even pass off the other end of the piece.

I could change to a brush method of applying the paint put each piece has over 120 letters on it. If I can get this worked out with spray paint it would be best. I just checked and I'm currently using Krylon spray enamel. I would consider the purchase of an airbrush if:

- I knew it would work well for this task

- It dosen't have a steep learning curve

- I can afford a good set for a reasonable amount (< 150 $ ?)

Acrylic or lacquer - are both available in spray cans and would they behave better than enamel?

Thanks again for the help.

- Dave

Re: Help with stencil process

#7

Try a Critter

Stuart Johnson

>I could change to a brush method of applying the paint put each piece has over 120 letters on it. If I can get this worked out with spray paint it would be best. I just checked and I'm currently using Krylon spray enamel. I would consider the purchase of an airbrush if:

- I knew it would work well for this task

- It dosen't have a steep learning curve

- I can afford a good set for a reasonable amount (150 $?)

You might want to give a small sprayer like a Critter a try. It can be adjusted to give a thin spray. The paint is stored in a small mouth pint Mason style jar with very easy clean up. I've used mine for everything from primer to lacquer. I've never used an airbrush but I think it works on the same idea, air blows across a nozzel and sucks up and sprays the paint.

Re: Help with stencil process

#8

Re: Thanks and more info

tek-Brunswick, Ohio

>Ok, it sounds like you have pretty good technique. You need to change product. I'd experiment on some scrap with the lacquer and the acrylic. They both typically build up less than the enamel. They may also be less likely to smear under the wipe on finish. Use as few coats as possible and allow adequate drying time before finishing over them.

Tom

Re: Help with stencil process

#9

Re: Try a Critter

John Lucas

>I've read all the responses above and I think an airbrush is the way to go. You can put on a much thinner layer of paint to get the same job done. If your having trouble with the paint running when applying the poly put a coat of shellac on first. That would form a protective barrier and if the paint your using is not alcohol solvent sensitive then it won't cause a run.

I have played with The Critter but only for spraying odds and ends finishes and spray masks. It's not as controlable as an airbrush by anymeans but it is way less expensive. I hate to see youspend $39 or whatever they are now and then find out that you still need to spend $150 or so on an air brush to get the job done right. Whatever you do don't buy a cheap airbrush. they simply arent' worth the hassle. Been there done that.

Re: Help with stencil process

#10

Re: Try a Critter

RobinCorell

>If you opt for an air brush you might consider using ink.

Robin Corell

Re: Help with stencil process

#11

Leaning toward an airbrush

Dave Belser

>OK, Looks like I can get a good airbrush "Kit" for about $70. I think I need a single action brush, not really sure about other brush options. The big question is can I use my "portable" contractors air compressor with the brush? I can use the existing regulator or add a lower range one in front of it, along with a moisture trap. What do I look for in an airbrush and will this compressor setup work?

Apparently the airbrush will spray just about anything that can be thinned enough. Using ink is an interesting idea but isn't that like using a stain? If I seal the wood to control bleed under the mask how will the ink stick?

- Dave

Re: Help with stencil process

#12

Re: Leaning toward an airbrush *LINK*

Gary R

>I'll do a little follow up now that I have an idea of how much you will actually be stenciling.

I would agree with an airbrush - stencil brush if you didn't have so much to stencil.

As far as compressor, yours is fine. You will need an in-line filter to keep out the water. Regulator you have should be fine - you need very little air.

As far as a brush, I have two. One is a Badger that I paid $175.00 for, and the other is shown in the link below. For you application - I would go with the one shown below.

I did a lot of small craft items for shows, and did tons of stenciling because it gave great details, was quick and looked nice.

I hand cut stencils from mylar, and airbrushed. Reason was...... you could get a very crisp edge with no build.

Single action brush - (like low cost model shown) - you set the paint flow, and just push the button.

Double action - press down for paint, and back for more air.

Dick Blick also sells some special airbrush paints. I used airbrush acrylic, thinned with water. This paint seems to have more pigment, and still gives a nice color when thinned. Use a little of their recommended thinner instead of water. I was doing quicky products that were not as demanding.

Just a little paint, very thin and a lot of air will give you a nice crisp stencil. Go over light, and keep moving. It dries almost immediate.

The Aztek series of brushes also works well. Last I checked, Walmart stocked one of them by the Model kits. Also at AC Moore or Michaels craft stores.

Hope this update helps.


http://www.dickblick.com/zz250/58/