Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Find a woodworking club near you

OK, what's the trick?

Posts

OK, what's the trick?

#1

OK, what's the trick?

Carole Valentine

>I am trying to burn a separation groove. Tried some #19 stainless steel wire - no burn. Tried some picture hanging wire - no burn. Not even a hint of brown. Is there a specific type of wire that you are suppose to use? What speed do you need to get the burn? I can't put a whole lot of pressure on it because the burning the groove was a bit of an afterthought and there is a fairly small section attaching the piece, so maybe that is my problem?

Re: OK, what's the trick?

#2

High speed.. *LINK*

Jennifer@Indy.USA

>Carole,

I use a potter's clay cutting wire that I found at my local art supply store. I use high speed to get the results I want. These work great for me and already come with little wooden handles attatched.

Look here to see what I'm talking about.

Jen


Clay Cutter

Re: OK, what's the trick?

#3

Re: OK, what's the trick?

Michael Stafford

>Carole, the burn is achieved by friction. You have to apply enough pressure so that the wood rubbing against the wire heats up and burns. Sorta like rubbing two sticks together except one of them is a thin piece of metal wire. You may not be able to apply enough pressure if your piece is fragile. Hope this helps.

Re: OK, what's the trick?

#4

Re: Small Hint

Mark Mandell - Gone Round In Jersey

>Don't forget to form or at least start the groove with your skew first. |;-}

Re: OK, what's the trick?

#5

Re: OK, what's the trick?

Jerry-Huntsville, AL

>You need to generate heat through friction with pressure and speed, the more speed and/or pressure the more friction and therfore more heat. If you can't put enough pressure on to get it hot you might try a small thin piece of dark oily wood (kind of like a wide popcicle stick). That may provide enough heat or stain from the wood to make a decent line.

Jerry

Re: OK, what's the trick?

#6

Re: OK, what's the trick?

Bill Howatt

>Some woods burn easily and some are a lot more difficult. Maple seems to burn just by looking at it the wrong way. But like everybody said, it is the friction producing the heat that does the work.

Bill

Re: OK, what's the trick?

#7

Re: OK, what's the trick?

john lucas

>If you can't get enough speed or pressure try wraping the wire around the piece so more of it is in contact with the wood. this creates more friction as well.

Re: OK, what's the trick?

#8

Obligatory safety precaution

Larry Winton

>Don't forget to keep your fingers from being wrapped by the wire. When it starts to burn, the wood grabs the wire a bit, so be prepared for that.

Re: OK, what's the trick?

#9

Re: OK, what's the trick?

georgetroy

>Carole I use copper wire most the time. Put wood handles on each end, I think you know that already. As the other comments said use the skew to v-groove. GT

Re: OK, what's the trick?

#10

Formica???

adrien

>though I've never tried it, I've read of using a piece of formica to burn the groove. Jennifer's comment about speed is, I think, more cogent than that of pressure. Spin a piece fast and sandpaper gets kinda warm. Same applies to burning.

Watch your fingers in either case. and don't spin an unbalanced piece at high speed DAMHIKT

Re: OK, what's the trick?

#11

Re: OK, what's the trick?

Bart Rhoads

>Make sure you dont have any finish or wax on your piece. This burning should be done on clean wood before and finish is applied. Also some woods are rather oily and they are very hard, if not impossible, to burn with wire.

Also I would not rap the wire around your piece as suggested by John Lucus. I tried this ONE time. It jurked the wire out of my hand and broke the vessel I was working on. But only skint my nuckle thank goodness.

Re: OK, what's the trick?

#12

Re: OK, what's the trick?

Steve in NC

>Carol

I use stranded copper wire. Be sure to burn the grove before you put on a finish, particularlly a wax finish.

If you have trouble getting enough heat, your wire may be too smooth or dirty. Try rubbing with 120 sandpaper.

Be sure your wire is not too long. The extra wire acts like a heat sink. I use small dowels on each end to act as handles.

Good luck

Steve

Re: OK, what's the trick?

#13

The answer is...

Terry Quiram, Roanoke Illinois

>a guitar string, one of the wrapped ones. As already suggested formica is an excellent material to achieve a burn. Use a corner and kinda, sorta sand the sharpe edges a little and apply pressure.

Terry

Re: OK, what's the trick?

#14

Re: OK, what's the trick?

Ron in Drums PA

>I use 6"-7" from a guitar string (G) mounted between two handles. I also use formica chips. I start by cutting a groove with a skew and crank up the speed. Takes a few seconds to complete.

Re: OK, what's the trick?

#15

Re: OK, what's the trick?

Jerry Whitaker

>Carole,

Just as John suggested, wrap the wire around the piece a little more, just until you start feeling some resistance. This is where you will get your maximum effect. Go beyond this point and you will be in trouble. DO NOT wrap the wire around your fingers as suggested. Also, a piece of formica will work. You can go to Lowes or Home Depot and get some of their samples pieces. They work fine. I forget whether it is Lowes or HD that has the largest samples, like 2x3 inches. You can also grind down an edge or a corner to make it a little thinner if you want a slightly thinner line.

Re: OK, what's the trick?

#16

Dick Hines

Re: OK, what's the trick?

Dick Hines

>Carole, I use copper wire. Other wire will work I just have access to copper. For a wider band you can use the counter top chips from the building supply store. They are free and work well. And you don't have to worry where to put the hot wire. When my supply gets low I just make a trip to Lowe's or Home Depot.

Re: OK, what's the trick?

#17

Dick Hines

Re: OK, what's the trick?

Dick Hines

>I did not read all the post but make sure you don't hold the wire in your bare hand. If not one said anything about that they should have.

Re: OK, what's the trick?

#18

Re: And the other answer is:

Allen Neighbors

>If you don't have a guitar string, a bicycle brake cable will also work. That's what I use. It might be a bit wider than you like. Any wire will work. It's just that you've got to have the right combination of pressure and speed....Something you can't have with a fragile piece. I've had the wire wrapped around a goblet, where both my hands are on my side of the lathe. Just watch what you're doing, and maintain control at all times. Hope this helps.

Allen

Re: OK, what's the trick?

#19

I give up!

Carole Valentine

>Well thanks folks, but no go. I tried my wires on maple and it burned fine, even at 800 rpm, but this dogwood absolutely refused even at 1600 rpm. The wire was so hot I burned MYSELF with it. Didn't have any formica to try as some have suggested. Ended up coloring the groove with a fine marker. Must be something about the dogwood. I know it is pretty hard and dense. It was nothing important...just a practice hollow form which I then played with by gilding the top third and burn texturing the bottom two thirds. Fooling around with a rich/rustic contrast. It's destined for the burn barrel. Thanks for all the responses!

Re: OK, what's the trick?

#20

Re: I give up!

RussFairfield

>Good luck trying to burn Dogwood with friction. Dogwood casehardens from the heat. That's why all of the little bobbins, spools, and wheels that thread passed around and through on textile machinery were made from Dogwood in earlier times.

Re: OK, what's the trick?

#21

Re: I give up!

Carole Valentine

>Whew! Thanks Russ! Guess that explains it. I will know not try that again.

Re: OK, what's the trick?

#22

Re: OK, what's the trick?

john lucas

>Bart I hope I didn't say wrap the wire around the piece. What I meant was wrap it further around the piece. I usually wrap the wire about 180 degrees or a little further. This produces a lot of friction with very little pressure. I would agree with you that wrapping the wire completely around the piece would not be safe.

Re: OK, what's the trick?

#23

Re: Obligatory safety precaution

David Breth

>I'll toss another safety hint out there - I would recommend avoiding areas close to the chuck, and when you do it, apply pressure, but not so great that you could slip. If that wire slips into the spinning chuck, the game will be on for sure.

David B.

Re: OK, what's the trick?

#24

Re: OK, what's the trick?

georgetroy

>Carole you get in more trouble than any turner I know about. LOL At least you talk about the project. Whereas many of us just keep quiet about it, don't say anything and don't learn. Keep up the good work and posting. Thanks for taking the time. GT