Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Reach the woodworkers who ACTUALLY BUY

Best method for turning platters and plates

Posts

Best method for turning platters and plates

#1

Best method for turning platters and plates

Ellis Walentine, Host

>I know it's been answered before, but I wanted to see if anyone has a really quick and sure fire way to turn a platter or plate from a round disk of wood without using a screw chuck or sacrificial faceplate block. I used to have a set of Oneway elephant jaws or whatever you call those things, but they melted along with everything else in the great fire of '99.

I've probably turned a hundred plates in my life but I never recall any feeling easy to do.

Any help?

Ellis

Re: Best method for turning platters and plates

#2

Re: Best method for turning platters and plates

tek-Brunswick, Ohio

>How big of platter or plate? I like to use my chuck jaws in expansion mode. I can incorporate my recess into the foot and not waste as much thickness of the stock. I make the first recess with a Forstner Bit. The # 2 jaws on a Talon chuck fit in a 2 1/8 hole nicely. I only need the recess to be 1/8" to 3/16" deep. If it is a big platter, I start out with the 2 1/8 D recess and use it to make a larger recess on the opposite side, Big enough to fit my # 3 Jaws.

Re: Best method for turning platters and plates

#3

Re: Best method for turning platters and plates

albertabob

>Try turning a suitable foot and hot glue it on your plate.

You can do the same thing on the finished side and flip it over to work on the back.

p.s. hope you have an infinite speed lathe. - accidents happen at high speed and plates have a lot of circumference relative to their thickness and like to vibrate if possible.

Bob

Re: Best method for turning platters and plates

#4

Re: Best method for turning platters and plates

Carole Valentine

>I have a disk mounted to a faceplate and I just attach the blank with good double sided tape. Am chicken to do this for anything over about 10 inches though. Gets any bigger than that I use the faceplate and screws.

Re: Best method for turning platters and plates

#5

Re: Best method for turning platters and plates

Jennifer@Indy.USA

>Ellis, I'm in the middle of a platter right now. The round blank was 16" diameter x2" thick. I just use the super strong double sided tape and stuck it directly to a 3" faceplate. Then I turned the bottom to shape and made a tennon about1/4" long. Of course I used the tailstock for support until the very last cuts on the tennon. I don't know if this was a "scary" way to do it or not. But I never felt like it was unsafe. The double sided tape I buy comes from Craft Supplies and is wicked sticky. To get the platter off the face plate I just put a slice of a 1" dowel about 1/4" thick inside the threaded faceplate and screw it back on the spindle to push the platter off the faceplate from the sticky tape. Wally told me of this easy removal method. It saves you from having to bang and chisel and pry it off.

Anyway...that's how I do it.

Jen

Re: Best method for turning platters and plates

#6

Re: Best method for turning platters and plates

John Lucas

>Ellis I used my vacuum chuck with the last one I did. It was a square platter 16" across the diagonal. I use an 8" homemade vacuum chuck faceplate. It holds very securely.

Re: Best method for turning platters and plates

#7

Re: Best method for turning platters and plates

Rick Allen

>When I was first starting out, less than 2 months into my turning life, I used a 8" disc trued up on a 4" faceplate with double face tape to turn a 24" Zebrawood table top and 18" shelf. It was a swivel head lathe so there was no tailstock to help. The top came off the tape twice but I ended up with a piecrust table. At that point I became a fan of double face tape.

Now I have a bigger swing lathe. I generaly start a plate between a Stronghold with #3 jaws and the tailstock. The jaws of the chuck drive the platter blank.

After the blank is made round I make a trueing pass across the tailstock side. In the middle of the tailstock side I cut a shallow tennon.

Remount the stock in the chuck, with the tailstock for support true up the tailstock side. At this point I decide which side will be the top and which will be the bottom.

I turn and finish the rim area.

Depending on which side is the top I turn the rim/body interface with the top side faceing the tailstock. (I may need to have turned a shallow recess if I fiped the plate)

Make a few passes across the face to extablish the slope to the body of the platter.

Back off the tailstock and finish up the body of the platter.

Sand and apply the finish of choice to the top and rim portion of the underside of the platter.

Mount the platter in cole jaws and finish turning the bottom. Sand and finish the bottom.

Wait a couple of days, then buff it all.

This works on platters up to 19". Most of my platters are between 14" and 18".

Good luck

Richard


img

Re: Best method for turning platters and plates

#8

Re: Without Screw Chuck or Face Plate

Dick Anderson

>Mount the disk between enters with the bowl (top) of the plate/platter at the headstock.

Turn the bottom side (portion at the tail stock) to what ever shape you want (ogee, etc.) and cut either the tenon or dovetail (your choice) for your scroll chuck. If I want a dovetail I use a bedan ground at the angle that matches my Vicmarc chuck jaws. As an alternative you could cut the tenon for a jam chuck.

Sand and finish the bottom.

Mount the platter/plate stock on your scroll chuck or jam chuck and turn the upper or rim and bowl portion. Sand and finish the rim/bowl.

Reverse the plate using cole jaws, vacuum chuck or other method for securing plate/platter. If you used a tenon on the base you can reverse the plate against your scroll chuck jaws separated with soft leather, rubber or tissue protecting the plate surface from the jaws. The plate can be accurately aligned using the original live center indent. The base (tenon area) can be completed up to a small area (circle) at the tailstock, provided you are using the cone shaped live center. Clean-up the small indent area off the lathe.

This is how you can do a plate or platter without a face plate or screw center; however, I do use the screw center when I have a cut blank with a fairly smooth surface, otherwise the above method when I have an uneven or odd shaped piece of wood.

Re: Best method for turning platters and plates

#9

Re: Best method for turning platters and plates

Bill Hale

>Ellis

I do all my work as Dick does except I always use a tennon.

Start between centers.

Cut outside shape including the tennon.

Reverse into a jaw chuck and finish turning and sanding. At that point I also do a first coat of spar varnish sanding sealer with the lathe on. I spray and wipe off with a rag. Comes to a very nice polish.

I have many sizes of pre turned fixture center pieces with a tennon on them.

I insert a fixture in the jaw chuck and remount the piece against the wood and bring the tail stock back against the original hole on the tennon.

Turn off the tennon down to about 3/8 for an 18" piece. Finish the bottom and remove from the lathe.

Sand off the tip left in the middle and done.

Good turning and be safe

Bill in Casa Grande,AZ.

Re: Best method for turning platters and plates

#10

Thanks, Richard

Ellis Walentine, Host

>I like the idea of jamming the raw plate against the #3 jaws with the tailstock to get the initial tenon. That saves the hassle of gluing a waste block (or taping it) to the blank.

Nice platter in that photo, by the way.

Ellis

Re: Best method for turning platters and plates

#11

Great tip, Jen I'll remember that one.

Ellis Walentine, Host

>

Re: Best method for turning platters and plates

#12

Good one, John

Ellis Walentine, Host

>I have a 16" walnut piece right now and it has some checks in the crotch sections. I'm not sure I can pull a vacuum on this, but maybe I can plug any leaks and give it a try.

Thanks,

Ellis

Re: Best method for turning platters and plates

#13

Re: Good one, John

John Lucas

>Ellis It's amazing what a little saran wrap will do.

Re: Best method for turning platters and plates

#14

Gotta love hot glue!!

Brian Simmons, Heflin, AL

>For me on the 12" and smaller, it's an expansion chuck 1/8" deep turn the bottom. Follow that by hot glue to a plywood faceplate. In my experience the bottom should be final sanded but no finish applied. I soften the glue with a heat gun and use a putty knife to work it loose. With the bottom already sanded, any hot glue left can be rubbed off.

For larger than 12" I use hot glue to do both sides. The largest I have turned to date using hot glue is 26" with my rpm around 300.