Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Price drop on over 1300 Rockler items

Flap Wheel abrasives??

Posts

Flap Wheel abrasives??

#1

Flap Wheel abrasives??

RussFairfield

>Am I the only one who uses flap wheels for sanding??

I was using one of them on the inside of a goblet last night, and was wondering why I never see flap wheels or small mops among the sanding methods that woodturners talk about and use. They are available in a lot of different diameters, widths, and grits, and there are a lot places where these work better than a disc.

Re: Flap Wheel abrasives??

#2

Re: Flap Wheel abrasives??

Ron in Drums PA

>Actually, I don't.

How do flap wheels stand up compared to sanding drums and sleeves? I bet the answer is "A whole lot better!"

I just may have to give them a try. Thanks Russ.

Re: Flap Wheel abrasives??

#3

Re: Flap Wheel abrasives??

Matthew fallon(long island ny)

>i dont really either but would like to try them.

the ones i saw at klingspor looked like they'd work terrific.

right now im pretty in love with the mirka abranet/abralon. really great stuff! doesnt load up at all really ,though i never used on gree wood yet.

Re: Flap Wheel abrasives??

#4

Re: Flap Wheel abrasives??

georgetroy

>I use the flap wheels on a limited basics have for some time. Klingspor is a good source for these. I just recently purchase some 1" flap wheels, they did not work too stiff. I super glued some cloth sandpaper between the flaps now, they work. The flaps must be fexible enough to fit down inside the goblet, vase or hollow form. I use extensions where needed. You can also glue on the end of the flap a small ring of sandpaper to get the nib. Good post Russ. GT

Re: Flap Wheel abrasives??

#5

Re: Flap Wheel abrasives??

Gary in Zirconia, NC

>I use them occasionally but they don't seem to be very aggressive. Are there some that are better than others? I just use them inside hollow forms.

Re: Flap Wheel abrasives??

#6

Keith Tompkins

Re: Flap Wheel abrasives??

Keith Tompkins

>HI Russ, Woodcarvers Supply sells flapwheels designed especially for carvers, they smooth surfaces, but don't affect fine details...haven't tried them yet...but sound interesting.

Re: Flap Wheel abrasives??

#7

Re: Flap Wheel abrasives??

John Lucas

>Russ I don't use flap wheels much. I had trouble with the courser ones leaving lines on the edges of the wheel. I prefer the mops but don't have any right now. They are kind of expensive. Do you have any suggestions.

Re: Flap Wheel abrasives??

#8

Re: Flap Wheel abrasives??

Les Robison

>I use flapwheels on any vessel that has an opening of 1" or greater. They are a God send for getting the interior smooth. I use 80 grit up to 180.

Les

Re: Flap Wheel abrasives??

#9

Re: Flap Wheel abrasives??

Phil Joines Krum, Texas

>I have some but don't use them much, too slow.

Have you tried stars?

I made several mandrels in different lengths from 1/4" rod, threaded 10-24 in the end. 3/8" rod for pieces more than a foot deep and a fairly large opening. Rip some 1" wide strips, poke a hole in the middle and mount them on the mandrel with washers and a round head screw. For multiple grits just unscrew one and screw on the next. I use about 8 to 12 strips each depending on the stiffens of the backing.

The length depends on the width of the turning and the opening. I want the strips to expand against the sides from centrifugal force. I run them about 700 RPM.

If anyone's interested I can shoot some pics tomarrow.

It's nothing to get into a flap over :>)

Re: Flap Wheel abrasives??

#10

2 Stars

Phil Joines Krum, Texas

>Here are two of the sanding stars. The complete ones are 1/4" by about 4" and 6" long. The other one is 3/8" x 12".

I used drill rod because it was handy, cold rolled would work just as well. If you use drill rod don't let it get hot while drilling, it could harden on you making tapping impossible.

The screws are 10-24 x 1/2" round head. Use a new tap. Dull taps are almost guaranteed to break in a deep hole. I use a #25 bit to make tapping a little easier. A #24 is standard. These are threaded about 3/8" deep.

The short piece is the hole cutter for the sandpaper. It's 1/4" W1 with a #4 hole. The drill came out the side while drilling which I thought had ruined it. Not. Turns out it makes it self cleaning. After drilling the end was tapered to an edge with 320 grit paper. It was then heated to bright cherry red and quenched. A few slots were cut with a Dremmel cut off disk. It will cut through a whole stack of strips at once.

I haven�t tried this but when sanding something a lot larger than the star adding foam disks to the shaft to stiffen the paper might make it work better.


img

Re: Flap Wheel abrasives??

#11

Re: 2 Stars

Allen Neighbors

>Phil, thanks for posting this photo and giving the instructional for these star sanders. I think these will work for vase interiors pretty well. I also believe I'll try the foam on the shafts to support the wings in larger vessels.

Thanks again. It's posts like these that help us novices.

Allen