Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

A55 Smoothing Plane

Cole Jaws Timely Reminder (Bloody Picture)

Posts

Cole Jaws Timely Reminder (Bloody Picture)

#1

Cole Jaws Timely Reminder (Bloody Picture)

Peter Charles Fagg

>Friends, I have just been reading the thread on Cole jaws and felt compelled to make a contribution to the forum.

I stupidly used my Cole jaws to hold a piece last year that I was making for an exhibition deadline. I had turned for about 8 hours in a very hot shop. I was tired but determined to finish just this one bowl.

99 times out of a hundred if something comes loose on the lathe I jump to one side and let nature take its course but on this occasion I made a grab for the piece and stuck my fingers between the segments of the Cole Jaws! It damn near ripped off my fingers, well one of them at least!

It was interesting to see the tendons moving, though!!!

Hospital beckoned and 10 sutures later I returned home with a very swollen hand and a battered ego.

It happens SO quickly, even after 15 years of turning there is always that tiny moment of loss of concentration. BEWARE!

It was just the one finger that suffered, but it could so easily have been my whole hand!

The piece did eventually make it to the exhibition!!!

Regards Peter.


img

Re: Cole Jaws Timely Reminder (Bloody Picture)

#2

OUCH!!!!

Rick Davenport

>

Re: Cole Jaws Timely Reminder (Bloody Picture)

#3

Re: Cole Jaws Timely Reminder (Bloody Picture)

adrien

>Don't know about cole jaws, but after chewing up my palm on protruding segments of my Vicmarc chuck, I've put a segment of inner tube from a tire (like a large rubber band) over that section of the chuck. So the next time I put my hand in jeopardy it won't suffer as much damage.

Re: Cole Jaws Timely Reminder (Bloody Picture)

#4

Dick Hines

Re: Cole Jaws Timely Reminder (Bloody Picture)

Dick Hines

>Well thet seales it. No supper for me tonight.

Sorry about the finger.

I learned long ago not to grab anything leaving a chuck. When I firs started turning I have a small bowl come loose form the chuck. I made a grab for it and my thumb went between the chuck and the tool rest. Of coures I yanked the thumb out but riped the pad of it right off. Tooks over a month before I could hold anything in my left hand.

Never how bad life would be if man did not have thumbs.

Re: Cole Jaws Timely Reminder (Bloody Picture)

#5

JL

Re: Double ouch! Don't do that!

JL

>

Re: Cole Jaws Timely Reminder (Bloody Picture)

#6

Re: Cole Jaws Timely Reminder (Bloody Picture)

john lucas

>Charles Glad you didn's suffer anything worse. I took a class under Don Russell at John C Campbell and he had the really big jaws installed on thier big lathe. It sounded like a propeller going around. I was scared to death every time I turned on it. After seeing your hand I'll stay scared, that way I'll stay away from it.

Re: Cole Jaws Timely Reminder (Bloody Picture)

#7

Re: Cole Jaws - another Darwin Award.

albertabob

>I fellow I know made these jaws from 1/2" MDF to evade buying a commercial set.

He apparently cut it so thin that when he reached across the spinning jaws his sleeve caught on a wing and it blew off leaving the next jaw to slice his forearm to the bone like and axe.

One of the dangers with lathes is over confidence and of course, really bad safety design re the position of controls on our lathes.

The worst offender in my estimation is the Reeves pulley designs that make you cross over the danger zone are to adjust the speed.

Of course long sleeves and poor design don't help much either.

I'm not sure I would countersink stove bolts like this on 1/2' MDF either.

Mdf is not recommended for tensioning bowls.

Bob


img

Re: Cole Jaws Timely Reminder (Bloody Picture)

#8

Re: Cole Jaws Timely Reminder (Bloody Picture)

Bill Hale

>As most of you know I end my post with" good turning and be safe".

I try my best to push the safety issue but we all have to remember that is why they are called ACCIDENTS.

When you think you are tired QUIT for a while or the day.

When your arms or hands get tired TAKE A BREAK.

Keep the shop quiet so you can hear your wood.

Don't over strech your tools and lose leverage.

Hold the tools properly.

Use sharp tools.

Push your limits but don't be stupid about it and respect fear.

The list goes on and on but theseare some of the most important ones I can think of now.

As I said Good turning and be safe

Bill in Casa Grande AZ.