Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Support WoodCentral when buying things you need

Chuck Safe Driver - Should OneWay make one? *LINK*

Posts

Chuck Safe Driver - Should OneWay make one? *LINK*

#1

Chuck Safe Driver - Should OneWay make one? *LINK*

Craig Daymon

>There are a LOT of OneWay owners in our turning group. If not lathe owners, most everyone at least owns a chuck. (I'm in the chuck group with a Talon.)

At our meetings, it has often been mentioned about how wonderful the OneWay Safe Driver is, especially for those teaching new turners.

It has also been frequently mentioned how nice it is to use the Chuck Spur Driver, which locks into a OneWay chuck without having to ever remove the chuck from the lathe.

OneWay says the Chuck Spur Driver is to allow you to put a large piece between centers to turn a tenon so it can be mounted in the chuck. (A little different from using the Safe Driver, which would be used primarily for spindle work.)

Several of our group mount the Safe Driver in the chuck, even though it is a Morse Taper fit, and clamp down on it.

I suggested to OneWay that they make (that there might be a market for) a Chuck Safe Driver, which I'm thinking would be than using the Safe Driver with a Morse Taper in the chuck. They asked me to solicite opinions from our group at a demo this weekend and I thought I'd ask here as well.

Link below to OneWay's Chuck Spur and Safe Driver page.

Thanks in advance for your input,

Craig


OneWay's Chuck Spur and Safe Driver

Re: Chuck Safe Driver - Should OneWay make one? *LINK*

#2

Re: I'd buy one...

Paul in Phoenix, AZ

>...I use my safe driver for all my spindle work.

Re: Chuck Safe Driver - Should OneWay make one? *LINK*

#3

Re: I grab a Morse taper ....

JamieDonaldson

>... drive spur in chuck jaws all the time, esp. when doing demos. Saves a lot of time and doesn't interrupt the proceedings to look for missing objects like chucks in unfamiliar shop surroundings. I also mount jam chucks made for the chuck jaws- saves killing time and possibly dropping the chuck on my foot with many eyes watching!

Re: Chuck Safe Driver - Should OneWay make one? *LINK*

#4

Re: Chuck Safe Driver - Should OneWay make one?

Don O.

>I love the spur drive in either the Talon or Stonghold. A Safe Driver for them would be great. I would definitely buy one. Great idea!

Re: Chuck Safe Driver - Should OneWay make one? *LINK*

#5

Re: Chuck Safe Driver - Should OneWay make one?

Bill Crommett

>Anotyher mystery in the definition department. Just what is a SAFE DRIVER ?

Re: Chuck Safe Driver - Should OneWay make one? *LINK*

#6

Follow the link in the original message.

Craig Daymon

>OneWay explains the benefits.

Re: Chuck Safe Driver - Should OneWay make one? *LINK*

#7

Re: Follow the link in the original message.

Bill Crommett

>So some brillient taxonomist has decided to change the name of the cup driver ! Next thing you know they will change the CPS to hertz or pounds to liters.

Re: Chuck Safe Driver - Should OneWay make one? *LINK*

#8

Re: Chuck Safe Driver - Should OneWay make one?

Tim Grenville-Cleave

>Sorby shift enough Stebcentres in assorted styles, one of them fits into a chuck ... give me the steb any time ... much more flexible than the Oneway.

Just my �0.02p worth

Tim GC

Re: Chuck Safe Driver - Should OneWay make one? *LINK*

#9

Re: Chuck Safe Driver - Should OneWay make one?

John Lucas

>I just open the jaws on my Vicmarc and insert my #2 morse taper 3/4" 4 prong drive center in the spindle. It sticks out far enough to be used this way.

Re: Chuck Safe Driver - Should OneWay make one? *LINK*

#10

Re: Chuck Safe Driver

RussFairfield

>I must be missing something. How can anyone use the friction from a cup-center to drive a piece of wood? You folks must be taking unbelievably light cuts, or using unrerasonable tail-center pressure.

Spindle turning should be using the minimum force between the head and tail centers to avoid bowing the wood and inducing vibration. The only way I can get a cup-center to drive the wood is too use an unreasonable amount of tail-center pressure, and that will cause more problems that it can solve. Reducing the pressure to anywhere near a reasonable amount doesn't give enough friction to turn the wood reliably. I guess that is one definition of "safe".

I want a positive drive on the wood with the least amount of pressure from the tailstock, and I can't do that with a dead center driving the wood.

As a compromise, I filed teeth into the edge of the cup. This gives a better grip on the wood, while still allowing slippage if something goes wrong. That makes it into a Steb-Center without the spring loaded point. The only reason I use this at all is because the profiles of both centers are the same and I can swap ends without getting out of round.

Re: Chuck Safe Driver - Should OneWay make one? *LINK*

#11

Re: Chuck Safe Driver

John Lucas

>Russ That's why I don't like the steb center. To compress the center spring far enough to get the teeth to engage there is too much pressure on the spindle. I also don't like the safety center but have used it on heavier inside out turnings to help hold the wood togehter. I use a 4 prong drive center. Push it in with the tailstock until it's seated and then remove as much pressure as I can and still make the spindle turn. This removes as much chatter as possible. Like you probably do when I'm doing a production run I'm hogging off wood. The safety center would not work for me.

It seems to me there are two things going on here. One is turning bowls or hollow vessels between center and not removing the chuck. The other is spindle turning using the safety center. To me they don't go together. I don't want the chuck in the way when I'm turning spindles so I remove it. Consequently I don't need a drive center that fits in my chuck.

When turning bowls it's kind of handy but Bestwoodtools along with oneway already have drives that fit in the chuck.