Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Good Hope Hardwoods - Walnut Slabs & Specialty Hardwood Lumber

Table top speed control for Power Carver

Posts

Table top speed control for Power Carver

#1

Table top speed control for Power Carver

Jennifer@Indy.USA

>Can anyone tell me where I can find a dial speed controller for my Wecheer power carver? The foot pedal and I are just not getting along. I'll be going along great and the next thing ya know I'm full bore on the gas! It's really a distraction for me. I know I've seen them somewhere....but where? I have a Traditional Woodworker catalog and a Treeline catalog in front of me and can't find one in either catalog. If anybody has any ideas....I'd love to get my foot off the gas and use a dial speed controller.

Thanks!

Yes, I can chew gum and walk at the same time :)

Jen

Re: Table top speed control for Power Carver

#2

Re: Table top speed control for Power Carver

Carole Valentine

>"Yes, I can chew gum and walk at the same time"

ROFL! Are you sure? Sorry I can't help with the table top control, but this just struck my funny bone. ;)

Re: Table top speed control for Power Carver

#3

Re: Table top speed control for Power Carver

Walt Drummond - Middlesex, NJ

>Jen,

How about a router speed controller? I bought mine a year or so ago and I think it was $39.00. A small box (3" x4"), has an off/on switch with a speed knob. Goes from almost 0 rpm to full speed. I think Woodcraft carries them.

Walt

Re: Table top speed control for Power Carver

#4

Woodcraft link *LINK*

Walt Drummond - Middlesex, NJ

>Try this link.


Router Speed Control

Re: Table top speed control for Power Carver

#5

Re: Table top speed control for Power Carver

Jennifer@Indy.USA

>Yes, Walt something like that! I wonder if that would work with this type of motor?

Jen

Re: Table top speed control for Power Carver

#6

Re: Table top speed control for Power Carver

john lucas

>Jen check www.riogrande.com They have a Foredom EM-1 manual dial speed control Part # 117-559 They also have the Foredom EMX manual control that works with the TX motors. They run $42 and $58. I am headed to the shop in a few minutes. I'll stick my router speed control on one of mine and see if it works. I haven't checked lately but they used to be $39. The slow speed is jerky and may not be that good for flex shafts. I'll find out. It will probably be after 10 before I get back online.

Re: Table top speed control for Power Carver

#7

Re: Table top speed control for Power Carver

Jerry Whitaker

>I think a router control would work on any motor that has brushes but don't hold me to it if you were to burn up your Weecher. I bought a router speed control from Harbor Freight for $14.95 on sale several months ago. Regular price was $24.95. The run on sale quite often.

Re: Table top speed control for Power Carver

#8

How about $29.95? *LINK*

Bob Elliott

>Jen,

I have this one, bought it with my system instead of the "gas" pedal. It works great!


img

Woodcarvers supply

Re: Table top speed control for Power Carver

#9

Re: How about $29.95?

Jennifer@Indy.USA

>Bob, that's just what I'm talking about....the price is right and it's made for these machines.

Thank you!

Jen

Re: Table top speed control for Power Carver

#10

Re: How about $29.95?

john lucas

>Jennifer That's a good deal and made for that purpose. I tried the router speed controller and it works well but I would go for the cheaper controller that's made for these machines.

Re: Table top speed control for Power Carver

#11

Re: How about $29.95?

Jennifer@Indy.USA

>Thanks for checking it John. I appreciate it. Good luck with your demo this weekend.

Jen

Re: Table top speed control for Power Carver

#12

Re: Table top speed control for Power Carver

Darryl Hansen

>Try www.traditionalwoodworker.com That is where I got my Weecher. As I remember you could get it with the foot or the table top controller. Phone 1-800-509-0081 Darryl

Re: Table top speed control for Power Carver

#13

Re: How about $29.95?

Ed Moore

>At Woocarver's Supply, the variable speed dial control is item # 797139

Ed

Re: Table top speed control for Power Carver

#14

Re: Table top speed control for Power Carver

Sterling Sanders

>Jennifer, I had the same problem. Couldn't concentrate on my carving and keep the speed constant. I'm using a Foredom foot control, so I don't know what your Weecher looks like. I drilled a hole through the top and bottom of mine and placed a bolt with a wing nut through the holes. You simply screw the wing nut up or down to change the RPMS. Simple and only costs a few cents. Hope this helps. Ster


img

Re: Table top speed control for Power Carver

#15

Re: Table top speed control for Power Carver

Jennifer@Indy.USA

>Now that is inovative! Why don't I think of these things?

Thanks for the idea Sterling...but It doesn't look like mine will work with this set up. I don't think.....

I appreciate it though.

Jennifer

Re: Table top speed control for Power Carver

#16

Thanks : )

Jennifer@Indy.USA

>Thanks everybody,

I appreciate your help...and inovative ideas!

I think I'll go with the one from Woodcarvers Supply. It's within my budget and I need a couple other things from them anyway...

cha-ching!

Jen :)