WE MOVED...
Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Have a question? Ask Woody!

Revolving Center:Need advice

Posts

Revolving Center:Need advice

#1

Revolving Center:Need advice

Chris DiCiaccio

>I have the Rikon Mini Lathe which came with a revolving cup center. I am only turning small, bowls, boxes, and vases. What do I need additionally as far as tailstock centers? I saw a 60deg cone for about $39. Then I saw they offer sets with cone, small point, etc.about 6 or 7 pieces for around $80. Oneway has a set for around $104. What is your advice as to what I realistically need? Thanks in advance.

Re: Revolving Center:Need advice

#2

Re: Revolving Center:Need advice

John Lucas

>Chris I use the cone center for 90 percent of my turning. I have the Nova live center which comes with different points. The cone center is my least used point. I doubt if I use it twice a year.

Re: Revolving Center:Need advice

#3

Re: Revolving Center:Need advice

Rick Allen

>Hi Chris

Most of the time you would like something pushing back at the headstock through the spinning hunk of wood. The live center you have now will do that just fine.

There are rare occasions where a different configuration is helpful. For example when I turn magic wands I use the live center for support. I don't want to apply pressure towards the headstock but I don't want the tailstock end of the wand flailing around either. In this situation I remove the point of the live center and apply just enough pressure so the live center spins. That way the tailstock end is kept from whipping about while eliminating compression on the spindle which would tend to cause the small cross section of a magic wand to bend.

The center you have likely has a removable tip.

On even more rare occasions I will need to put a fixture on the live center so I can center the work piece on a vacuum chuck.

All this to say that what you now have will very likely cause few if any limits to your woodturning adventures.

Re: Revolving Center:Need advice

#4

My 2 Cents worth

tek-Brunswick, Ohio

>Chris, I have the One-way center and the Sorby center that takes the multiple tips. I use the Sorby about 90% of the time. Both centers have work fine for me. The Sorby I like better for spindle and smaller turnings. The One-way big cone centers fit into cylinders, and it is preferred by a lot of bowl turners. The One-way is pretty heavy duty. The thing I like the least about the One-way is that, it is a lot longer. When I am not using it I need to slide the tailstock way back or take the center out of the tailstock. If you bump your elbow against that sharp point on the center a couple of times, you will know why it needs to be out of the way when not in use. I use the cup center with the point for working on stock that I want to use an exact center point. If I want to adjust where my center point as I turn I use the cup center without the center point. I see you have The Rikon Mini Lathe. That is a fairly short machine. I think that I would go with the shortest revolving center that would fit your needs. BTW how do you like the Rikon?

Re: Revolving Center:Need advice

#5

John,

Chris DiCiaccio

>"I use the cone for 90%", "The cone is the least used". Could you clarify on this. Thanks for responding.

Re: Revolving Center:Need advice

#6

Re: John,

John Lucas

>Chris I probably used the wrong term. Some people call this a cup center. The cup keeps the point from going in too far and also allows you to reposition work. That is that same point that comes standard on the Oneway live center. Mine is removeable,

Re: Revolving Center:Need advice

#7

Leo Van Der Loo

Re: Revolving Center:Need advice *LINK*

Leo Van Der Loo

>Hi Chirs

Chris I have several centers, Scoda heavy duty, no loose points or hollow, cheap short center that came with the midi lathe and a Oneway with all the pieces, so do I always use the Scoda, no or the Oneway, again no, or that little cheap one, also no.

If I could only have one live chuck for turning wood, I would choose the Oneway, but sometimes I like to be able to use the 1.1/2" that my Oneway is longer than the cheapie, any other time I use the Oneway, I use the Scoda when turning metal.

The Oneway would last you a lifetime and will be able to handle a larger lathe if/or when you upgrade to a larger lathe, it has all the advantages you could want from a top of the line live center, and I do not have any financial interest, to Oneway or a selling place of the center.

Read and look at the possibilities the Oneway gives you, and compare, you hear nobody complain when they bought the best, here's a direct link to the Oneway center if you like to have a look.

Have fun and take care

Leo Van Der Loo


http://www.oneway.on.ca/spindle/live_center.htm

Re: Revolving Center:Need advice

#8

Re: Revolving Center:Need advice

Phil Joines Krum, Texas

>It depends on what you turn. A live cup center with a removable point will do most things.

If I'm turning largish spindles or bowls I use the center with the point.

For long, thin stuff (1/4" thick and smaller) I like the type where the revolving part is just the center rather than the outside because it reduces rotating mass. This can be important if you need to stop and restart the lathe.

If I'm turning a long, thin spindle I want to be able to remove the point that most cup centers have. That lets me put the finished end of the spindle into the cup without damaging the end.

If I'm turning a goblet with a thin stem I want to be able to add a piece that will go into the finished cup of the goblet to hold it steady while the stem is turned. The piece could be metal like the Oneway if it's padded with paper towel. I prefer to make a centering piece of wood that is as light as possible to reduce stress on the spindle.

If I'm turning pens I need the point to hold the end of the mandrel.

If I'm turning metal I usually use a 60 degree machinist's center.

Re: Revolving Center:Need advice

#9

Tek, and all responders:

Chris DiCiaccio

>Thanks for responding. I'm weighing out all the replies to sort out what is best for me, hopefully before I purchase anything. As for the Rikon, its my first and only lathe and so far I am very pleased with it. I've had it since Christmas. I like all the features and the way it functions. The only question, which Woodcraft told me when I bought it, is whether it will hold up to the endurance reputation of the Jet. Remains to be seen I guess.