Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Nearly 100 Exotic Wood Species, Direct-Imported Since 1972. Shop Slabs & Turning Stock.

Need help with grinder

Posts

Need help with grinder

#1

Need help with grinder

RK in Milw

>I bought an 8 inch, two speed grinder from Woodcraft. Added the Oneway wheel balancers. What I can't figure out is how to tighten the nuts that hold the wheels on. The arbor turns when I try to tighten the nuts since there is no way to lock the arbor. Can't tighten the nuts against each other since they both tighten counter to arbor rotation. Suggestions will be greatly appreciated.

Ron Nelson

Re: Need help with grinder

#2

Re: Need help with grinder

jwoodwright

>Ron, unplug grinder, hold wheel with hand and tighten nut.

Caution: Overtightning can cause cracking/damage to your wheel...

Re: Need help with grinder

#3

Re: Need help with grinder

Russell L. Babbitt Jr.

>I just want to agree with jwoodright. Overtightening the nuts can put too much pressure on the wheels. The arbors are threaded the way there are so that the normal rotation helps keep the nuts secure.

Re: Need help with grinder

#4

Leo Van Der Loo

Re: Need help with grinder

Leo Van Der Loo

>Ron just like jwoodwright says, just hold the wheel and tighten the nut, the wheel gets tightened by the grinder while using if it they are not fully tightened.

There are strap wrenches but I have never used anything for changing or installing grinder wheels.

Have fun and take care

Leo Van Der Loo

Re: Need help with grinder

#5

Re: Need help with grinder

RK in Milw

>Thanks for the response guys, but that hasn't worked. Everthing slips.

Re: Need help with grinder

#6

Re: Need help with grinder

John Irvine

>I normally hold the wheel with a block of wood pried between the case of the grinder and the wheel

Re: Need help with grinder

#7

Me too

john lucas

>

Re: Need help with grinder

#8

Re: Need help with grinder

George Van in WI

>Ron, is it possible the nut is bottoming out on the shaft before hitting the washer?

Re: Need help with grinder

#9

Question

Carole Valentine

>Ron, I had the opposite problem - getting the nuts loose on mine. Don't tighten them too much. I have not tried the balancing because I have not needed it yet, but I read the Oneway balancing system says that it is suitable for wheels with 1 to 1 1/4" holes. I assume that means the size of the holes without the arbor bushings since I can't imagine a 1 - 1 1/4" arbor on a bench grinder. My WC 8" grinder wheels have holes much smaller than that even if there were no bushing. Was this a misprint? Did you have any problem using the system on the woodcraft wheels? Another thought...aren't the washers provided with the Oneway system flat where the ones that come on the grinder are sort of cone shaped? Would this allow the nut to run out of thread before it gets tight? Just a thought.

Re: Need help with grinder

#10

Here's what I do...

Peter Teubel

>Put ONE wheel on. Hold the other side of the shaft with vise grips (not on the threads, of course). Tighten the nut on the wheel with another wrench. Put the other wheel on. Hand tighten the nut as much as possible. Put vise grips on that nut. While holding the already mounted wheel, strike the vise grips once with a mallet to tighten the nut. Not hard, but a little more than a tap. This should snug up the nut enough to hold. If you strike to hard, you'll loosen the other nut. The idea is to apply a short duration tightening force enough to snug it up but not enough to loosen the other.

Re: Need help with grinder

#11

Re: Here's what I do...

Vicmarc.fan

>The Oneway balancing system comes in 1/2", 5/8" and 3/4" to fit the grinders spindle size. FYI if you plan to install a system on the new Delta VS 8" grinder the washer and bolt heads will not clear the cover so you have to turn the wheel assembly around. The system has a HR and a LH thread. When you turn the wheels the RH goes on the LH shaft or the thing tends to loosen over time.

Ron

Re: Need help with grinder

#12

Re: Here's what I do...

Carole Valentine

>Not talking about the arbor size.

"The Oneway Precision Balancing System is available in versions to fit �", 5/8" and �"-diameter grinder shafts. The wheels must have a 1"-diameter center hole regardless of grinder shaft size."

Re: Need help with grinder

#13

Leo Van Der Loo

More help with the grinder wheels

Leo Van Der Loo

>Hi Rick

There has got to be a reason why "everything slips" take of the wheel again and check the thread on the shaft and in the nut, clean it all up with a steel brush and install the nut by hand, it should go on smoothly all the way, if not, find out why, and also measure how far the nut will go on, you might need to have a washer on the shaft to take up some length, as the Oneway piece could be shorter than the previous assembly of washers and wheel.

Have fun and take care

Leo Van Der Loo

Re: Need help with grinder

#14

Re: Need help with grinder

RK in Milw

>Thank you all for the responses. Peter was on the mark with the nature of the problem and I ended up with his solution, The problem is that the surfaces of the Oneway balancer are very smooth and there was no friction against the paper labels on the grinding wheel. Does anyone ever strip the paper labels off?

The point about not overtightening is a good one and I will be careful with that.

Again, thank you all. What a great resource this forum is!

Ron

Re: Need help with grinder

#15

Re: Need help with grinder

Carole Valentine

>It is my understanding that those "labels" are called blotters and they are there for a reason - to compensate for any tiny irregularities in the washers and to keep the them from damaging the wheel.

Re: Need help with grinder

#16

Re: Need help with grinder

RK in Milw

>Thanks Carole. I didn't know that but I had a hunch I shouldn't peel them off.

Ron