Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Support WoodCentral when buying things you need

Question for Jennifer

Posts

Question for Jennifer

#1

Dennis in Southern Oregon

Question for Jennifer

Dennis in Southern Oregon

>Jennifer, I believe that you use Prisma Markers to color some of your pyrography pieces. Is there a secret to getting bright vivid color on wood turnings? I have been experimenting with them on madrone and on sycamore but seem to get rather washed-out color, even after applying several coats. Have you used any other product more successfully? Dennis

Re: Question for Jennifer

#2

Re: Question for Jennifer *LINK*

Rick Allen

>Hi Dennis

The colors can only be as vibrant as the background will permit. White wood like holly or bleached wood provides the best background for bright vivid colors. I have used Prisma Color on pine and the results were vivid.

Prisma Color markers are alcohol based. If you put a finish over the color it will likely dissolve the color. If you are careful the dissolved color will stay in place. Also Prisma Color isn't very light fast. These colors will fade with exposure to light (all colors will fade with exposure to light, just that Prisma Color fades faster than some other products).

Instead of Prisma Color...

There are water based colors but these require that you raise the grain a few times before coloring. There are reactive dyes which react with natural materials like cotton, wool, wood. These dyes tend to be very light fast. Because these dyes can be delivered with water instead of a solvent like alcohol you can apply solvent based finishes over them and expect the color to say in place. Many of the finishes we use darken the wood. Those finishes will also darken dyes as they are primarily a coating that is dark. Select a finish that is gin clear and this will not be an issue (as long as it isn't water based which will of course dissolve the dye).

I have purchased from Pro Chemical and found the product to be as expected. There are MANY other sources for these dyes. MX Reactive dyes is the product I have used. Mix with water and apply with a small watercolor paint brush. The minimum quantity is 2 OZ. You can buy "kits" which have smaller sized samples. That is a LOT of dye. Enough to make a quart or more of dye. I mix with a toothpick. The amount of dye I can scoop out with a toothpick, two or three times mixed with a soda bottle cap full of water will provide enough dye to color 5 or 10 square inches of wood.

It is always a good idea to try the coloring and finishing out on cutoffs so you have a better idea of what to expect.

Good Luck

Richard


MX Reactive Dyes at Pro Chemical

Re: Question for Jennifer

#3

Vivid Prisma Color

Rick Allen

>Forgot the picture of the vivid color turning that was done with Prisma Colors.


img

Re: Question for Jennifer

#4

Re: Question for Jennifer *LINK*

Jennifer@Indy.USA

>Hi Dennis,

I do use the Prisma Markers. I've never tried any other kind of artists markers so I have nothing to compare them to. Rick is correct. The colors will only be as bright as the background material allows them to be. So I like to use them on lighter woods. I have also bleached the area that I'm using the markers on prior to applying the color and this helps to allow the colors to look more vivid. I got some pretty good results on a little plate of cherry that I bleached the rim before coloring.

There a lot of others here that use the marker much more than me. I hope they chime in here. I know Andi Wolfe has used the Prisma markers extensiviely and I've never seen her post anything about them fading much. I'm sure if you leave a piece in the sun or under bright lighting they might fade a bit faster?

Hope this helps....good luck! Please post your results. We'd love to see them!

Jennnifer


Bleached Rim w/flowers

Re: Question for Jennifer

#5

Dennis in Southern Oregon

Re: Question for Jennifer

Dennis in Southern Oregon

>Jennifer, on the subject of wood bleaching, what do you use? I tried a hot solution of oxalic acid (brand name savogram) on a sycamore form the other day and could not see any effect after I rinsed and dried it. I only left it on for about 15 minutes though; is that too short?

Re: Question for Jennifer

#6

Dennis in Southern Oregon

Re: Question for Jennifer

Dennis in Southern Oregon

>Thanks Rick and Jennifer for your help. Dennis