Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Veritas - Innovation in Tools

Spalted maple hollowform

Posts

Spalted maple hollowform

#1

Spalted maple hollowform

Ed Kelle

>6" diameter. This has quite a few wormholes which I filled with epoxy and coffee grounds. Hollowed thru a 2" opening which was still a challenge for me. Ebonized walnut collar to go with the nice dark spalting lines. A bit flatter on the top of the form, but it was good practice anyhow. Finished with Deft then knocked down with steel wool to give a more natural appearance.

Any thoughts on this one?


img

Re: Spalted maple hollowform

#2

Brad Vietje

Re: Spalted maple hollowform

Brad Vietje

>Great job, Ed ! I think its a fine piece. I agree that the Ebony collar works well with the blackline spalting, though the collar doesn't look as glossy as the rest (?) From this angle the form looks fine -- I can't see that its too flat -- are you sure it is ?

Safe Spinning,

Brad Vietje

Newbury, VT

Re: Spalted maple hollowform

#3

I like it!

Dominic Greco in Richboro PA

>Ed,

I really like this! Even though I can see where you're saying it might be flat, I still think you did a nice job on the form.

Did you intentionally leave the collar flat black? If so, nice touch! I like it.

See ya around,

Dominic

Re: Spalted maple hollowform

#4

Re: Spalted maple hollowform

Barry Turner

>Just one. If you filled the worm holes with coffee grounds and epoxy, how are the wrorms going to get in and out?

Nice piece. The photo really shows off the figure of the maple.

Re: Spalted maple hollowform

#5

Re: Spalted maple hollowform

George Van in WI

>I like this one Ed, the knocked down finish looks appropriate. What did you do to ebonize the walnut? Makes a good poor man�s ebony! Is the collar finished in deft also? From this angle I have a hard time seeing a flat also.

Re: Spalted maple hollowform

#6

Re: Spalted maple hollowform

Jennifer@Indy.USA

>Ed, I really like this piece. The collar is great. I like that it has a matte finish. It almost looks lightly textured. Is it? You're kicking out some really great stuff here lately. I just love your work!

Thanks for the inspiration!

Jen

Re: Spalted maple hollowform

#7

Re: Spalted maple hollowform

GaryG in MD

>Nice form all around, Ed. I really love the collar -- you nailed it. ...Gary

Re: Spalted maple hollowform

#8

collar info

Ed Kelle

>Yes it sure is poor man's ebony. I made the solution by putting steel nails in a vinegar jar. You could also use steel wool. Though the trick is to shake it up. I had made batches that sat for weeks and did nothing until someone told me i had to shake it to get a reaction. I shake the jar every day and leave the cap open a bit to get some oxygen inside as well. I strain the solution into a new smaller jar before I use it. It will raise the grain so either wet the wood to raise the grain then sand before putting it on, or sand lightly after aplying and give another coat. It isn't textured, just some light flecks of walnut showing thru, which I think looks more interesting than a flat black. Finished with one coat of teak oil because it has a little varnish in it as opposed to plain watco. Considered putting on another coat, but I think I will leave it.

Thanks for all the nice compliments, now I will go ahead and glue the collar on , yes I was waiting to hear some reactions before I did this, so thanks!

Re: Spalted maple hollowform

#9

Re: collar info

George Van in WI

>Thanks Ed, I will give the vinegar/steel wool a try.

Re: Spalted maple hollowform

#10

Re: Spalted maple hollowform

Randy Gleck

>Very Nice Ed, I like the Collar on that, also like the flatter look of it. I think it works.

Randy

Re: Spalted maple hollowform

#11

re: ebonizing wood

Matthew fallon(long island ny)

>Heya ed' this ones really nice. i like the one you had at the last meeting. sure nice to be able to see your artwork close up and in person ;)

(we're in the same clubs,heh)

Ed i wanted to tell you an even faster trick i learned for this ebonizing method(just for making the rust part) what you really want to do is dunk the steel wool then squeeeze out the vinegar and let the wool sit outside in the air where it'll get more oxygen,this is what causes the reaction, you'll literally see and feel(it gets very warm!) the rust setting over the wood. i bet a fan in front of it would help even more ;)

after about 5 minutes i dunked it in and all the rust came off into the vinegar, i then repeated that about 6 times then got bored and jsu tleft it in... im trying it out on some ash,pecan,apple and african mahogany. the first coat 2 days ago made a nice even grey on all but the mahogany(i couldnt really tell much on it) especially the ash.. i added another thick coat last night and will chek it again today...

some other methods i've come across was using hydrogen peroxide instead(i believe both of these are just in order to dissolve the protective coating on the wool?) another was to use a dc converter like for a train-set and wrap the positive lead around teh wool/nails, and leave it overnight... i guess whatever method makes the most iron oxide the fastest would be the best way....

any other formulas for ebonizing out there?

Re: Spalted maple hollowform

#12

Re: re: ebonizing wood

Danny Wells

>I used Feibings black leather dye. That's definitely the fastest way I know and is really black. I used it on a maple rocker for my wife. It's relatively cheap and convenient. You can get it at any Tandy's store.

Re: Spalted maple hollowform

#13

Re: re: ebonizing wood

matt fallon

>just checked the woods,

ash wasnt much darker, nor the apple or pecan really..not enough tannins i guess.

but the walnut. wow. completely Jet-black.

Re: Spalted maple hollowform

#14

Re: re: ebonizing wood

RobinCorell

>I use Fiebings leather edge dye. it comes with a really convienient applicator top, kind of like liquid shoe polish. it is an analine based dye. I have used it with wonderful results by sealing the wood with a thin coat of laquer before applying the fiebings and following with a couple of coats of Jasco tung oil.

Robin Corell