Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

This is the most versatile work station you will ever use

Grizzy G0584 or G0462 or Other?

Posts

Grizzy G0584 or G0462 or Other?

#1

Grizzy G0584 or G0462 or Other?

Bob Entwisle in NJ

>Hi all.

I have never turned anything on a lathe, I've 'turned' a couple of tiny things on a drill press (cause I didn't have a lathe,) so my question is....

If I rise....(or as those on the flat side say, take the plunge down the slippery slope) to turning, Are the GO584 or G0462 lathes, which are within my budget, viable? Alternative ideas sought and welcome.

I'm thinking I just want to turn a few table legs...but I'm guessing that that's all anyone buying their first lathe thinks.....

I just do this as a hobby/obsession etc. Would one of the above allow me to turn a table leg and/or delve deeper into this unknown region of horizontal spinning things> :)

Thanks

Bob

Re: Grizzy G0584 or G0462 or Other?

#2

Re: Grizzy G0584 or G0462 or Other?

Steve in NC

>Bob

There have been many post about this questions. Do a search and you will get a bunch of opinions.

My two cents. Buy a Jet mini. I bought one after I got fed up with the vibration on my Delta iron bed and I really like it. Now I only use the Delta when I need the size. If you need the length for long spindles (or legs), get the jet bed extension but try it without first.

Good luck.

Steve

Re: Grizzy G0584 or G0462 or Other?

#3

Re: Grizzy G0584 or G0462 or Other?

john lucas

>Bob Get the 462. You'll have trouble finding accessories for the 1x12 threaded spindle. You'll also find 3/4 horse to be underpowered for 14 inch pieces. It's not bad up to 10 or 12. You'll really enjoy 2 horsepower.

The other one has a pivoting headstock but you'll find the tool rest can be a pain when the headstock is in the pivot postion. Then you have to realign it accurately when you go back to normal position. I had a pivoting head on my Nova and although it was great for hollowing bowls it was a hassle most other times.

You'll enjoy the 16" swing of the 462

Re: Grizzy G0584 or G0462 or Other?

#4

Re: Grizzy G0584 or G0462 or Other?

Rick Allen

>Hi Bob

The budget thing is one of those misunderstood aspects of turning wood. You think you have it all worked out. You think that budgeting for a lathe you can aford is the primary expense. Figure on $500 to $1000 in addition to the lathe and know that you are very likely to actualy speend about twice that much.

You will get better use out of the Jet Mini.

Re: Grizzy G0584 or G0462 or Other?

#5

Re: Grizzy G0584 or G0462 or Other?

Wayne Kuhn

>I bought the G0462 in January of this year. I believe it is a lot of lathe for the money. I have not turned on the high end machines. I have also posted my thoughts about this lathe in this forum. If you do prchase this lathe ,bolt it to the floor. It's performance is increased esp. for turning bowls.

Re: Grizzy G0584 or G0462 or Other?

#6

JL

Re: Grizzy G0584 or G0462 or Other?

JL

>If I had to go for one or the other, it'd be the G0462. Higher power, more common thread pattern. The extra length for spindles would be good. Alternatively, you could go for a Jet VS mini with a bed extension. That's close to the same price range. As stated in preceeding posts, stability (bolting it to the floor or adding a ballast box w/ some weight) would help a lot.

Re: Grizzy G0584 or G0462 or Other?

#7

Re: Grizzy G0584 or G0462 or Other?

Gary Evans Tallassee, TN

>Hi Bob,

If you have an interest in a used lathe with some accessories, I just put one up on the Classifieds board.

Gary


img

Re: Grizzy G0584 or G0462 or Other?

#8

Go with the G0462

Ray Carson, New Jersey

>Mornin' Bob,

First off, I'm no lathe or turning expert.

However, I am a Grizzly fan. I've said this at least a dozen times but it's worth repeating, Grizzly is not the best stuff out there but they do make quality machines. 90% of my machines are Grizzlys, only because their prices fit my budget and the machiines do the job for me. Of course I've made some improvements to suit my needs, like replacing my stock rip fence on my table saw with a Beismeyer and adding a mobile base and also a dust chute for the dust collector.

It all depends on your budget, and what you plan to use it for.

That being said, if you haven't researched it, do so. Consider Jet, Delta, Powermatic and so on and even the good stuff like a Oneway. Take a look at the website I listed. They have a lot of brands.

I recently purchased a Jet 708358K/JWL-1442VSK 14" x 42". I decided on this one because I wanted to try a different manufacturer. At the time I had a few bucks to spare and also I heard good things about it.

Now, if you told me your heart was set on the Grizzly then I'd say go for the GO462. Why? It's only $20.00 more than the GO584. It has more HP and I think it's a few pounds heavier. If I couldn't have afforded the Jet, then my second choice would have been the G0462.

I'm just returning to the spinning world of woodworking and I think either machine will be a good start for you.

As with most hobbyist woodworkers, such as you and I, we tend to progress in our tool purchases. We buy a machine to get a feel for it, then step up from there.

My 2 cents worth. Hope I helped.

Ray