Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Reach the woodworkers who ACTUALLY BUY

Mini Metal Lathe - Knurling Wood...Uh?

Posts

Mini Metal Lathe - Knurling Wood...Uh?

#1

Mini Metal Lathe - Knurling Wood...Uh?

David Lykins - Marietta GA - guitardude

>Yes I've always been a little different... so I've been making some guitar bodies of which I decided needed matching wooden control knobs. I make the control knobs by drilling a 1/2" hole in my knob blank, then inserting a 1/2" dia. bushing that gets a hole drilled and tapped with an 8/32 thread in order to accept an 8/32 set screw. The set screw is used not only to hold the knob on the potienometer (POT) for the volume and tone controls of the guitar, but also to lock it in place when I turn it on my metal lathe.

Anyway, I have a full size knurling tool that I'll have to grind down in order to get it to fit in my metal lathe. However, if its not going to knurl the wood I'm waisting my time.

So my question is, Is there a better way to get a knurled or textured type surface on a turned peice of wood. I doesn't have to cover the entire surface of the side, just something that looks good and would make it easier to turn.

Here's a pic that should give you an idea of the texture I'm looking for, my wood knob on the left (maple with a black walnut cap, also has a small pearl dot inlay on top) and a standard metal knurled knob on the right.


img

Re: Mini Metal Lathe - Knurling Wood...Uh?

#2

Re: Mini Metal Lathe - Knurling Wood...Uh?

Danny Wells

>You could checker it like on a gunstock. They do it on duck calls all the time.

Re: Mini Metal Lathe - Knurling Wood...Uh?

#4

Re: Mini Metal Lathe - Knurling Wood...Uh?

David Lykins - Marietta GA - guitardude

>Do you have any idea where I'd find information on Checkering wood or how it is accomplishied?

That might be a viable option.

Re: Mini Metal Lathe - Knurling Wood...Uh?

#5

Re: Mini Metal Lathe - Knurling Wood...Uh?

john lucas

>Dave The sorby tool only does cross hatching like that in very hard wood. Thier demonstrator showed me that it barely worked in Osage orange which is one of our harder woods. It runs over $100 if I remember correctly.

I used a large knurling tool on a wood lathe. I held it in a home made tool rest. Worked fair. It will only work if the tool is the same width as the knob because you don't have power feed of the tool.

I happen to have a small metal lathe and think I have a small knurling tool. I'll try to remember to look tomorrow and see. I may be aable to make the knobs for you.

Do a search of checkering on the web and you will find lots of sources for tools and techniques. There are power tools to do it and hand tools.

Re: Mini Metal Lathe - Knurling Wood...Uh?

#6

Re: Mini Metal Lathe - Knurling Wood...Uh?

Gil Jones

>Checkering info and all the tools.

http://www.brownells.com/categories.aspx?c=3961

Re: Mini Metal Lathe - Knurling Wood...Uh?

#7

Re: Mini Metal Lathe - Knurling Wood...Uh?

Don Evans

>Dave:

You can do it the same way they did it on the metal. For metal lathes as mentioned, they make a tool with wheels with the grooves cut into them. You can buy these in single wheel or double wheel tools, you want the double wheel as one wheel cuts the lines running one way and other wheel cuts the lines running other way therefore forming the diamond shape. This is like gunstock checkering except that is done by hand with a different tools and there is a large learning curve to go with it to become very good at it.

The double wheel, because one wheel is mounted above the other forms a "V" that the spinning knob (mounted on lathe) would fit into, forming all at one revolution. It would best be done with hand turning the lathe.

I'll put a link up when I find it that takes you to place to purchase the tool.

Don

Re: Mini Metal Lathe - Knurling Wood...Uh?

#8

Re: Mini Metal Lathe - Knurling Wood...Uh? *LINK*

Don Evans

>Here's the link for a double head model.

http://www.ares-server.com/Ares/Ares.asp?MerchantID=RET01229&Action=Catalog&Type=Product&ID=82771

Don


Micro Mark site

Re: Mini Metal Lathe - Knurling Wood...Uh?

#9

Re: Mini Metal Lathe - Knurling Wood...Uh?

Don Evans

>Forgot to add that John is right about the no feed part.

However, I don't see that as a problem, just push this tool against the knob centering it on the shaft. This will leave non knurled area above and below but to me that would be more attractive.

You can also pull the tool back away and move up knob and push it back in on another area, just don't run over where you have already knurl or it will look very bad.

Practice on scrap.

Don

Re: Mini Metal Lathe - Knurling Wood...Uh?

#10

Re: Mini Metal Lathe - Knurling Wood...Uh?

John Lucas

>Don I've been thinking about the feed thing and I think you might be able to feed it by hand. Knurlers work in the same fashion as the sorby spiraling tool and speed of feed is totally controlled by you. I think that is what I did for a mirror handle many years ago but my memory doesn't go back that far. I need to try that again because it would make a fun texture for turning. What I do remember is that some woods didn't work well. The knurling tool is basically crushing or mashing in the wood to create the textrue and some woods simply looked mushy.

Re: Mini Metal Lathe - Knurling Wood...Uh?

#11

Re: Mini Metal Lathe - Knurling Wood...Uh?

Jerry Bickenbach

>David

I think that that metal knurling tool pushes the metal in and it squishes (technical term) up a little to make the points. I also think that it takes a lot of pressure to move the metal like that. I would think that the wood would not like being crushed like that and the points would crumble rather easily.

I would suggest a series of straight groves or flutes up and down the side just close enough togeather to make the knob easy to turn and not leave sharp points that may break during use.

Jerry