WE MOVED...
Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

VPS-Level Performance. Fully Managed. No Hassle.

Jet mini slow speed.

Posts

Jet mini slow speed.

#1

Jet mini slow speed.

john lucas

>I finished playing with the Jet mini VS modification. Here are photos of the modification. I put a 1meg ohm potentiometer in series with the middle lead of the vs potentiometer. You can get the pot from Radio shack. A 500k pot would also work but doesn't reduce the speed quite as far.

The middle lead of the VS pot is white. I just cut that lead and ran a wire from that lead to one side of the 1meg pot. Then I attached the white lead from the board to the middle lead of the 1meg pot.

I drilled a hole in the top of the control box. Then I drilled a smaller hole for the pin that keeps the pot from spinning. I installed the 1meg pot in this hole. I didn't have a knob to fit it yet.

I'll post photos below of the modification. This should slow the lathe down to around 60 rpm. I don't know how much power will be lost so roughing at this speed may not be possible but you can adjust the variable speed knob to zero which will be around 500 rpm and then adjust the 1meg pot so it slows down to 300 or 400 rpm and be able to rough out of round pieces more safely.


img

Re: Jet mini slow speed.

#2

mounting hole for pot 

john lucas

>


img

Re: Jet mini slow speed.

#3

final installation 

john lucas

>


img

Re: Jet mini slow speed.

#4

Re: Jet mini slow speed.

Terry Quiram, Roanoke Illinois

>John

Great post. Are you going to add a reversing switch as well? For me to be able to make this change you would have to offer a step by step with clear photos otherwise all I can do is appreciate what you did. This seems like such a small thing. Why can't jet do this at the factory?

Terry

Re: Jet mini slow speed.

#5

Re: Jet mini slow speed.

john lucas

>Terry There are several good posts on how to add a reversing switch complete with drawing of the schematics and everything. About the only thing left out is where to mount the switch, and I may have missed that. There's plenty of room near where I mounted the pot. I may add that later. I'm not a reversing kind of guy but if I'm going to play with these things I might as well go all the way.

As to why Jet didn't do this sort of thing. My guess is that small lathes generally run at high speed for everything except larger out of balance bowls. They probably set the limit at 500 figuring that this gave them the lowest speed with acceptable torque. You can still stall it at this speed quite easily. I also don't know if what I did can damage some electrical component if you run at this speed very much under load. I ran it for 30 minutes but without a load.

Re: Jet mini slow speed.

#6

Re: Jet mini slow speed.

Bill Howatt

>I would also be concerned about the motor overheating. Since it is running slower than intended its fan (if it has one) will not be blowing as much air. Motors intended for inverter variable speed duty usually have higher temperature insulation. If heat is a problem a solution is to just mount a small fan to blow air on the motor.

Bill

Re: Jet mini slow speed.

#7

Re: Jet mini slow speed.

bob davis

>john,this is great info.i also wonder why so many mfg. think 500 is slow enough..granted you will lose torque at lower speeds but you adjust. ihad a nova mercury that went down to almost zero at any belt setting,,wish i had kept it..the first thing i had to do on my general 10 years ago was reduc the motor pulley size toget it down from 500 to 300..maybe lathe mfg need to have woodturners as part of the design group..thanks again,bob davis

Re: Jet mini slow speed.

#8

Re: Jet mini slow speed.

bob davis

>terry, go to http//www.frontrangewoodturners.com and you canget the inf with photos that john mentioned..

Re: Jet mini slow speed.

#9

Re: Jet mini slow speed.

Phil Joines Krum,Tx

>John,

I wonder how replacing the factory pot with one of 1meg + whatever the factory pot's resistance is would work? May not be able to get one that size.

Re: Jet mini slow speed.

#10

Re: Jet mini slow speed.

john lucas

>Phil I'll try it later and see. It should be easy to wire in. I think the problem is the the adjustment would be too course. The original pot is about 10K if remember correctly.

Re: Jet mini slow speed.

#11

Re: Jet mini slow speed.

Scott Greaves in Blackfoot Idaho

>Hi John!

It looks like you got it working!

Of course, the Jet Mini is a useful little lathe for just about any kind of turning you can fit on it! But as a penturner I can't help but think of it in terms of turning pens. A good low end speed is the one thing this lathe lacked. When they came out with the VS version, and it only went down to 500rpm, we were thinking like "Why bother?" Most penturning is best done at higher speeds. But sanding and finishing is better at slow speeds, particularly applying a CA finish to a pen. Putting CA glue on a pen rotating at 500rpm is still a bit exciting at times!!! But you have just solved this problem for a lot of penturners out there. And what do we care about torque when all you're doing is applying CA to a finish turned pen? It's not like it involves moving a lot of weight around!

Now, for my question. Would you mind doing an article on this modification that we could post on the penturners website? (www.penturners.org) Hundreds, if not thousands, would be grateful!

Scott.