Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Reach the woodworkers who ACTUALLY BUY

5 Questions

Posts

5 Questions

#1

5 Questions

Wayne Kuhn

>Being new to this bowl turning addiction, I have some basic questions that have come up in the last few lathe sessions.

1. Is the outside of the tree always the outside of the bowl? I Know this will maximize the size of the bowl, but does it always have to be this way? (actually thats 2 questions, BWTH)

2. When rough turning. Do you rough turn to final shape as close as possible?

3. Does the inside of a bowl usually to match the outside?

4. How long and what diameter do you make your tenons for chuck mounting.

I understand there are very few absolutes in this addiction. However your thoughts on these matters would be greatly appreciated.

Gotta run I hear a chainsaw outside.

Thanks for your input,

Wayne

Re: 5 Questions

#2

5 answers, which lead to more questions

Raymond Overman in SC

>1. Is the outside of the tree always the outside of the bowl? I Know this will maximize the size of the bowl, but does it always have to be this way? (actually thats 2 questions, BWTH)

No, the outside of the bowl doesn't have to be the outside of the tree. You do have to take into account wood movement and accept that depending on where you cut the blank from the log, it will dry differently leaving different warping patterns. There are books and videos on this very topic. Maybe someone can suggest a few.

2. When rough turning. Do you rough turn to final shape as close as possible?

I do, just to get a feel of the grain and patterns that my final product is going to have. Plus it's good practice at curves. I even sometimes do finish cuts for the practice knowing that I'm going to be doing them again.

3. Does the inside of a bowl usually to match the outside?

Usually so that the bowl will not crack due to stresses caused by thick spots and thin spots moving at different rates. Other design factors may influence thick and thin as well.

4. How long and what diameter do you make your tenons for chuck mounting.

I make mine about a 1/8"-1/4" shorter than the jaws I'm using with a slight dovetail in. You do not want to bottom out the tennon in your chuck jaws.

Re: 5 Questions

#3

Re: 5 or More , Um, Responses

Mark Mandell - Gone Round In Jersey

>"1. Is the outside of the tree always the outside of the bowl? I Know this will maximize the size of the bowl, but does it always have to be this way? (actually thats 2 questions, BWTH)

2. When rough turning. Do you rough turn to final shape as close as possible?

3. Does the inside of a bowl usually to match the outside?

4. How long and what diameter do you make your tenons for chuck mounting."

1. No - your choice [2 ans, er, responses]

2. Depends - There are those who turn wet/green to final shape and then allow the piece to warp as part of the drying process. Others, who turn green to a general shape but leave heavy (thickness of at least 10% of diameter) and then return when dry. Your choice - different looks.

3. When turning green/wet wood, an even wall thickness and slightly thicker bottom will help prevent cracking and splitting during the drying process. The is no requirement that the inside and outside curve match on the final bowl.

4. Personally, I cut the tenon as big as the chuck jaws will take (especially when roughing green wood). Length should be just slightly less than the depth of your chuck jaws so that the rims of the jaws contact the body of the bowl before the end of the tenon bottoms against the chuck. This makes for a much more stable hold.

M

Re: 5 Questions

#4

Re: 5 or More , Um, Responses

Mike Schwing from Md.

>I'd like to second Mark's suggestion to make the tenons as large as your chuck jaws can accomodate, but for a different reason.

As the blank dries, the tenon will go out of round/true as does the bowl, often enough to prevent for a solid hold in the chuck for the 2nd turning. If the tenon was turned large, it will be possible to mount the bowl between centers and retrue the tenon without making it too small for those same chuck jaws.

This is not a calamity should it occur however. You can always use smaller jaws if you have them OR you can turn another tenon and glue it onto the one that is now too small.

Re: 5 Questions

#5

Re: 5 answers, which lead to more questions

Rick Davenport

>Re: #1

Turning Green Wood by Michael O'Donnell

Has some excellent information on different grain orientations for bowls.

It's a great resource for all sorts of stuff.

I find myself referring to it regularly.

Enjoy.

Rick

Re: 5 Questions

#6

Re: 5 Questions

Wayne Kuhn

>Thank you , Mark,Mike,Raymond and Rick for your prompt reponse and answers.

My intuition was correct on 1-4. But off on #5. I was turning my tenons about 2" round and about 1/4 long on a 10" blank.

I will start making them larger.

BTW- I can add add 2 orbits and 1 explosion to my expierience file.

No Harm done to me shop or tools. Just the undergarments.

Re: 5 Questions

#7

Re: 5 Questions

Gerry Meekins in Maryland

>Hey Wayne,

Next time you are at a BAT meeting take the Bill Grumbine DVD home with you. These questions and many more that you are bound to have in the future are answered.

Keep um Spinnin! (And duck -n- cover!)

Gerry