Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Support WoodCentral when buying things you need

Sears Buffing Compounds

Posts

Sears Buffing Compounds

#1

Sears Buffing Compounds

Mike in Fort Walton Beach, FL

>Hi All,

I was at Sears this week-end and noticed they carry flannel buffing wheels (at least in six inch size, eight inch wheels were on back order and it didn't say cotton or flannel on it) with a quarter inch hole for mounting. Seems like just the right size since I mostly do just little stuff. They have a broad range of buffing compounds but I need some opinions. They have a bar called brown tripoli which I am assuming is like the tripoli in our catalogs. It even says it's for wood. They also have a small range of rouges (white, green, blue, and I think maybe red). It looked like the white rouge was coarser than the tripoli. So I'm wondering if the tripoli might be the same as the brown tripoli and if the white diamond might be the same as the white rouge? It seems like I can get away with a buffing system to suit my need for twenty dollars. I would probably eventually move up to the Beall system but I'm still learning how to finish. I'd appreciate any thoughts on the matter.

Thanks,

Mike

Re: Sears Buffing Compounds

#2

Re: Sears Buffing Compounds

tek-Brunswick, Ohio

>The Tripoli should be the same. I'm not sure about the white rouge though. White diamond compound is pretty common. It is used to polish stainless steel. The truck stops even sell it for polishing truck wheels. I'm sure that you can make the Sears wheels work. They might not give quite as high of gloss, because the Sears wheels use a harder courser fabric, than the Beal system.

Tom

Re: Sears Buffing Compounds

#3

Re: Sears Buffing Compounds

Mike in Fort Walton Beach, FL

>Thanks Tek! I can't remember, which I'm supposed to use first, the white diamond or the tripoli. I've never buffed before and this is just kind of an experiment, but they also have the green and blue rouges which are supposed to be the ones that make the ultra high shine in metals. Think those might compensate for the lower quality buffing wheel? I think the blue is the finest grit they offer.

Mike

Re: Sears Buffing Compounds

#4

Re: Sears Buffing Compounds

tek-Brunswick, Ohio

>Tripoli is the first step. Depending on how much gloss you want, sometimes it is enough. Remember to let your finish cure good and hard before buffing. Letting a Danish Oil cure 2 weeks before buffing would not be out of order. If you are doing small items you can buff them on the lathe. Just rub the compound into a small piece of cotton cloth and hold it lightly against the turning. Do NOT wrap the cloth around your fingers or the turning if it gets caught it could cause seriouse damage to your fingers or hand. Some turners will not use cloth at all on a spinning turning. They use paper towels instead, because they will tear before any damage is done.

Tom

Re: Sears Buffing Compounds

#5

Re: Sears Buffing Compounds

James McClure

>If I remember correctly, the downside of those wheels at Sears is that they are stiched throughout the wheel which makes them pretty stiff. If you look at the Beall wheels they are only bound at the arbor which gives them much more flex. You can really push a peice into the Beall wheels and the wheels spread out and cover more area. The other downside is that they are pretty narrow. You may want to cut through some of the stiching to give the wheels more flex and bundle two of them together. That is from what I saw there a while ago. They may have a better selection now.

I've also seen some cloth wheels and buffing compounds at Harbor Freight so you may want to check there too.

Re: Sears Buffing Compounds

#6

Re: Sears Buffing Compounds

Mike in Fort Walton Beach, FL

>Thanks James. The flannel buffing wheels aren't stiched as far out as their cotton wheels. Online they have many more options as well. I think it's worth experimenting with. I might even try the ultra fine grit rouges just to see. I won't be at the next meeting because my folks are coming down to visit that week-end and it's the start of the last week with my wife before I go to Maryland for retraining. The downside is that I heard from my chief of assignments and I'm not coming back to Eglin. No word yet on where I'm going to be stationed but my wife is staying for the next year and a half to finish the nursing program. That means the house stays and my lathe may have to stay with it. I'll post when I find out where I'm going to be stationed. Might be able to say farewell at the July meeting if I'm still in between retraining and my assignment.

Mike

Re: Sears Buffing Compounds

#7

Re: Sears Buffing Compounds

James McClure

>Oh bummer! I hope you can make it to the July meeting so we can give you a proper send off.

Hope your training assignment goes well!