WE MOVED...
Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

VPS-Level Performance. Fully Managed. No Hassle.

AAAARRRRRGGGGGGHHHHHH!!!!!

Posts

AAAARRRRRGGGGGGHHHHHH!!!!!

#1

AAAARRRRRGGGGGGHHHHHH!!!!!

Mike in Fort Walton Beach, FL

>I'm having one of those days (so I'm just venting, feel free to share your stories of a bad day)! I came home all excited because I finally (after about two months) got my Wolverine grinding jig set up. I had to cut some wing looking things off the side of my grinder, but got it to work in the end. I tried it out last night on a spindle gouge. Man is that thing sweet. So today, I looked online to see if I got the fingernail grind that I was going for. Nope, bevel was off and it looked more like an irish grind bowl gouge. So about an hour later and a half inch of my gouge gone, I decided since I was apparently good at getting side grinds, I should see if I could do it on a bowl gouge. Apparently not. I know tools are consumables, but an inch and a half total in one night without even turning anything! I don't think I can afford to replace them all at once. As I type this I'm downloading the videos from Oneway's site on using the jig since I'm having just a bit of difficulty with the written version. I think I'll look at them tomorrow, I'm just too frustrated to bother with it tonight. I'm an eternal optimist though and am not going to go to bed upset. Life's too short for that. Hope everyone else is having a good day. I just needed to vent for a few and now I'm going to wash the HSS dust off and hit the sack. Then tomorrow after work, I'll watch the video. If I still can't get it right, I'll drive to the first turner's house I can find that has one of these monsters and watch in awe as they show me in three minutes how to use it right and get me to master it in another five :-). Night all!

Mike in Ft. Walton Beach

Re: AAAARRRRRGGGGGGHHHHHH!!!!!

#2

Re: AAAARRRRRGGGGGGHHHHHH!!!!!

Rick Davenport

>Sounds like you're having one of those nights where it is best to just walk away and do something entirely different.

I just finished a nice tiger wood perfume pen for a special order.

All put together and finished.

Except the wick is sitting on my bench looking for something to do.

Can I borrow one of your "short" gouges Mike?

I wanna beat that pen to a woody pulp!

AAAAuuuuuugggggghhhhh!

Rick

"Life shouldn't be dull."

Re: AAAARRRRRGGGGGGHHHHHH!!!!!

#3

Re: AAAARRRRRGGGGGGHHHHHH!!!!!

Chris K in MD

>Mike,

I was equally frustrated with the wolverine when I first got it. I learned a trick from a guy at the craft supplies booth. Make a stop block to get a repeatable distance from the end of the varigrind. Set the angle of the vari grind then use the arm adjust ment in and out to get where you want to go. I traced the angle he had setup on a 8X11 sheet and got it close and now only move the arm (under the wheel) in or out. I found that this really helps becuase there are some many different adjustments you can make.

Re: AAAARRRRRGGGGGGHHHHHH!!!!!

#4

Re: AAAARRRRRGGGGGGHHHHHH!!!!!

Skip Beardsley

>Mike,

Keep after it, you will wonder how you ever cut anything after you master the tool and get really sharp tools. It is worth all the arrggggg you have had.

Skip

Re: AAAARRRRRGGGGGGHHHHHH!!!!!

#5

Re: AAAARRRRRGGGGGGHHHHHH!!!!!

Phil Joines

>Been there, done that ">) You can use round bar to practice.

Re: AAAARRRRRGGGGGGHHHHHH!!!!!

#6

Re: AAAARRRRRGGGGGGHHHHHH!!!!!

Colin Spencer

>Mike, If you want a trip to sunny Spain I'll show you how to use it!! Please persevere it will be worth it, it takes about 30 seconds to touch up a gouge once you are used to the jig, it only needs one sweep round to put a new sharp edge on your gouge. For bowl gouges I use the arm locked to the second most oblique notch and for spindle gouges use the arm at it's most upright position. If you need help I'll take photos? The block with a hole is a great way to go but a quicker method is to use the length of the large piece of angle iron that the grinding arm sits in this is also about 2".

Re: AAAARRRRRGGGGGGHHHHHH!!!!!

#7

Re: AAAARRRRRGGGGGGHHHHHH!!!!!

tm

>Rick, youre not alone on that one... GRRRRR!

I spent $$$ on a slow speed 8 inch Delta grinder & Kelton Multi Grind System. It took me a long time to get it assembled & running. My idea was to buy and do practice grinds

on cheap gouges from Harbor Freight and master the various

grinds BEFORE buying the Sorby tools.

I still haven't mastered it.

And yep, they are getting shorter.

From what I've been reading in books and on the net this is probably

the most frustrating aspect of turning for the beginner to intermediate level turner such as myself.

I think Phils idea is even better of using round stock to practice on.

I know what its like to use a tool with a good edge and get nice finish cuts. And I know that on the other side of the learning curve

it will be worth it.

Better days ahead...

tm

Re: AAAARRRRRGGGGGGHHHHHH!!!!!

#8

Re: AAAARRRRRGGGGGGHHHHHH!!!!!

Mike in Fort Walton Beach, FL

>Thanks all for the encouragement. I'm sure today will be a better day and I'll try all over again.

Mike in FWB, FL

Re: AAAARRRRRGGGGGGHHHHHH!!!!!

#9

Re: AAAARRRRRGGGGGGHHHHHH!!!!!

OB OBrien In Pensacola

>Mike; sorry your having problems. Here's some info for you.

Read the instructions on the installation of the rig to your grinder.

1. It's important that the grinder sit on a 3/4 inch thick piece of plywood to obtain the correct angles and relationships.

2. Check the distance of the center line of the grinders shaft to the front of the rig.

3. Look at the video on the Oneway site for the varigrind. It's an excellent video and is really informative.

4. If all that fails, call Floyd or me and we can maybe set you straight.

Good luck

OB

Re: AAAARRRRRGGGGGGHHHHHH!!!!!

#10

Re: AAAARRRRRGGGGGGHHHHHH!!!!!

Mike in Fort Walton Beach, FL

>Will do OB. I'll follow up either tonight or tomorrow with the results of further experimentation. Thanks for the tips.

Mike

Re: AAAARRRRRGGGGGGHHHHHH!!!!!

#11

Re: AAAARRRRRGGGGGGHHHHHH!!!!!

Dinyar Chavda

>Mike:

If all else fails, get the Sharpening DVD from the AAW tha thas Bonnie Klein, John Jordan and others on it. A great explanation of the principles behind sharpening, plus some tips on how to get started, both freehand and with the jig.

The video is free with a new AAW membership.

Re: AAAARRRRRGGGGGGHHHHHH!!!!!

#12

Re: AAAARRRRRGGGGGGHHHHHH!!!!!

Steve in NC

>Mike

Stay with it. It took me a while to learn how to use the jig but it works like a charm now.

As others have said, the video is very helpful. I also use the stop block. I have also made pencil marks on the sliding bar so I do not have to use trial and error each time. I just use the stop block to set the exposed length of the tool, slide the bar to the mark and sharpen. 30 seconds at most.

A couple of other hints. Be sure your wheels are clean and square. If not you are wasting your time. Also, be sure yuor jig is parallel to your wheel. If it isn't your grind will not be symetrical.

Good Luck and stay with it.

Steve