Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Urban Salvaged Hardwood Slabs, Milled In-House from Rare Trees. Shop Unique Walnut Stock.

A sanding technique

Posts

A sanding technique

#1

A sanding technique

David Breth

>Several months ago, I asked for help in a post about sanding tearout areas on bowls. Most responses suggested using a substance on the tear out areas that would help make the fibers stand up, but I think it was Mike in Thunder Bay who offered a response that really got me thinking - he said basically, "hey, put water, milk, honey, thinner, oil, whatever on it to help the fibers stand up". I took his message to heart, and started a method that I like a lot.

When I finish with the tools, I take a bar of paraffin wax, and coat the area to be sanded. Some of this is done with the lathe spinning, some while it is stopped. The idea is to fill in all those nasty areas, and while I'm at it, I coat the entire area to be sanded, just to make sure imperfections are coated as well. Then I begin sanding with the lathe at low speed (my lowest speed is 600 rpm), usually with 100 grit to start. I go through several pieces of sandpaper, because all you pick up to start with is a bunch of wax. I stick with 100 until "all" the wax is gone, and I've got a smooth, soft surface of wood before continuing to subsequent grits (which you should do anyway). I then run the table on grits up to 600. (Because of the relatively high rpm I'm dealing with for sanding, I've developed a pretty quick wrist action to prevent scoring lines from the sandpaper.) By the time I'm done, the bowl is baby-butt smooth.

As I've gotten better, there are fewer and fewer defects on my end product, and the most recent bowl I can't keep my hands off because it is so blasted smooth. Patience with the 100 is a virtue to get all that end grain nice and purty.

Positives about the paraffin wax:

1) It keeps the wood "cool" during the most aggressive sanding phase.

2) The results have been very good

3) Paraffin wax is cheaper than say, sanding sealer, and is available at supermarkets.

4) It does not color the wood

5) It keeps the dust down during the most aggressive phase of sanding.

6) I would rather not use sanding sealer or any chemical substance that will go airborne.

Negatives:

1) You go through a lot of 100 grit.

At first, I used leftover minwax tung oil, but found that the oil was penetrating better in some areas than others, so sometimes I got more sandpaper aggression on one spot than another. Also, I sometimes ended up with dark spots where the oil penetrated quite deep. The wax fills gaps rather than absorbing into the wood, and therefore doesn't seem to encourage greater material removal in one area of the bowl than others.

I'm interested in your comments. I know this is not a new topic, and I'm sure I'm not breaking any new ground here, but I don't think I've seen anyone mention using wax in this way, and I've found it to be a very nice solution.

David B.

Re: A sanding technique

#2

Re: A sanding technique

Jennifer@Indy.USA

>Hmm...very interesting David. I've honestly never heard of anyone using paraffin wax before? That's that stuff made by Gulf? Comes in bars, right? Looks white? One Question I would have is where ever that wax has filled or penetrated the fibers....what happens when you put an oil finish on it? Or a wipe on poly? Does it show up then?

I may have to do some experimenting myself. Thanks for the info!

Jennifer

Re: A sanding technique

#3

Re: A sanding technique

David Breth

>The wax is completely gone (or molecularly close to it) by the time you apply finish. I don't change from 100 grit until the wax is gone and the surface is defect free.

And yes - that is the exact wax I'm describing. I guess I should have mentioned another positive, in that, the wax has a very low melting point.

David B.

Re: A sanding technique

#4

Re: A sanding technique

John Lucas

>I was wondering the same thing as Jennifer. I use Johnsons paste wax when I'm sanding the inside of my boxes but this is the finish I use on the inside. I usually start without using the wax and then start using the wax at around 320 or so.

Re: A sanding technique

#5

Re: A sanding technique

David Breth

>I tried paste wax as well, which I rarely use as a finish, but tried for this purpose. In those cases, I ended up with some penetration into the wood that never quite got sanded out, and which was visible in the finished product. Paste wax is a pretty liquidy wax as you know, and when I was using it my sanding technique wasn't as good anyway.

Re: A sanding technique

#6

Re: A sanding technique

Wally Dickerman in Arizona

>I suggest that instead of working on sanding skills you work on tool skills so that you can discard the 100 grit and wax. When you find end-grain tearout it may be because you were cutting against the grain. Cutting with the grain gives you a much smoother surface. When you do find torn grain, apply some finishing oil and shear scrape. You should, in a very short time have a surface that doesn't require heavy sandpaper grits. A plus is that you save money on sandpaper

Wally

Re: A sanding technique

#7

Re: A sanding technique

Wally Dickerman in Arizona

>I'll add that when you start sanding, apply the same finishing oil with the first grit you use. You'll be pleased with the results. I'm sure that using parafin wax does the job but I'd be surprised if the heat from sanding doesn't melt some of it into the wood. That might be okay with some finishes but might adversly affect others.

Wally

Re: A sanding technique

#8

Re: A sanding technique

David Breth

>I certainly try to improve tool work all the time, but the need to sand isn't going to go away, and I think this technique could apply regardless. Regardless of the first grit used, the first few pieces of sandpaper are going to gather a lot of wax and not a lot of wood.

I've used the oil finish I intend to use a few times for this purpose, but I prefer the wax I guess. Plus, I don't always know what I'll use as a finish when I'm in the sanding phase.

It wouldn't surprise me if wax remained in the wood at the end of this, but I really think it would be a tiny small amount, if any. The deepest the wax will go is the depth of the roughest area, and the sanding will go at least to that depth to get a smooth surface. By the time I get to 180 (my next step from 150), I'm getting dust, and no more wax building up in the sandpaper.

The piece I'm working on now is cherry, and I applied the first coat of oil last night - it was probably the smoothest finishing surface I've worked with yet, and the oil took really well. (I'm planning on posting it when it is done, because while the form is terrible, the finish promises to be pretty nice.)

David B.

Re: A sanding technique

#9

Re: A sanding technique

James McClure

>I think a rub down with alcohol, mineral spirits, or something like that would dissolve any residual wax.

Re: A sanding technique

#10

Re: A sanding technique

Phil Joines

>Try using a cabinet scraper before the 100 grit. I should take most of the surface wax off.

Re: A sanding technique

#11

Re: A sanding technique

JKJ in East TN

>I've used beeswax for the same thing, although what I have is a little harder than paraffin. (you can also get paraffin from utility candles) Often, apply wax, then use a scraper to fight the tearout - cabinet scraper works well. Once the major tearout is gone, sand as normal.

JKJ

Re: A sanding technique

#12

Andy DiPietro

Re: A sanding technique

Andy DiPietro

>Sounds like an interesting technique. You may want to wipe the bowl down with Naphtha before applying your finish. Naphtha strips out wax without leaving a residue. I am curious what type of sandpaper you are using? I just ordered �Wet or Dry Sandpaper Sheets, Silicon Carbide, 9� by 11� from Amazon.com. They carry all the grits from 60 to 2500. I am going to experiment further with sanding with finishing oil. I tried tung oil, Waterlox and I will try Watco Danish oil next. I think I will add the wax to my experiment.

Thanks

Re: A sanding technique

#13

Re: A sanding technique

David Breth

>I've been using 3M sandpaper. From memory, I've got the following grits: 60 (I'm pleased to announce I haven't used this in quite awhile, but it lives on the bench with the other sandpaper), 100, 150, 180, 220, 2something else, 320, 400, 600.

Re: A sanding technique

#14

Re: A sanding technique

Barry Irby

>Why not wash the sand paper with naptha? Maybe naptha is more expensive than sand paper?

Re: A sanding technique

#15

Re: A sanding technique

Greg in Oshkosh

>Dave

I've been doing something similar for a few years now. I use a mix of 50% wax and 50% turpentine. It is a soft paste and goes on real easy. I then just sand it off. I have never never had a problem with a finish over the top of this, since like you said, the wax is gone before you get through all the grits. I believe that I got this technique from someone on this forum or the newsgroup. It works extremely well on endgrain inside of bowls. I have given away over 50 bottles of the wax-turpentine mix to other turners and reports have all been positive.