Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Precision you can feel — woodworking perfected with Lee Valley

Powermatic guard bracket adapted to dust collector

Posts

Powermatic guard bracket adapted to dust collector

#1

Powermatic guard bracket adapted to dust collector

jared

>remove 1 for email

I have attempted to resize my pictures to show, per a request, how I fastened my dust collector to the guard mounting bracket on my powermatic lathe.

I used a 3/4 inch dia steel rod, drilled a hole in it so that the little spring pin in the bracket would lock it in to position. Then I made the bracket that slides on the end of the rod and actually holds the dust hood. I cut off a short section of 3/4 inch water pipe, drilled a hole in it and welded a nut on so that I could use an old hand screw to lock it on the shaft. Then I welded a 3/4 by 3/4 by 1/8 angle about a foot long on to the water pipe. Then you can swivel the bracket in and out and back and forth to position it where the hood will do the most good picking up dust. The hood itself is actually made from an old aluminum heat lamp hood that my dad used years ago to keep baby pigs warm. I just cut a hole in the top of it, leaving some tabs that I duct taped on to the dust collection flex hose. I just used a bungee cord to hold the hood onto the angle iron bracket, that way you can slide it up and down the angle bracket to get it in the right position. I had to think about this whole set up for a while but it eventually all fell in place. I hope the pictures come out ok. Jared


img

Re: Powermatic guard bracket adapted to dust collector

#2

Another picture from a different angle

jared

>Here is another picture taken from the front of the lathe with a roughed out bowl attached to show how the whole thing looks.

It looks like my picture resizing actually worked ok. Jared


img

Re: Powermatic guard bracket adapted to dust collector

#3

Re: Another picture from a different angle

DougJ in Crawfordsville, IN

>Thanks jared,

That gives me some ideas for what to do with mine.

Re: Powermatic guard bracket adapted to dust collector

#4

JL

Re: Powermatic guard bracket adapted to dust colle

JL

>Good idea. I use a stand for my setup.

Re: Powermatic guard bracket adapted to dust collector

#5

Re: Powermatic guard bracket adapted to dust colle

Norm Smith in Nova Scotia

>Hi Jared,

I did the same thing with the steel bar but I built a plywood box about 20" high 12" deep and 9" wide and drilled holes into the upper back part so it fits on the bar and can slide along easily. The box just catches the bottom of the bed for stability but can be tilted forward if there is a need to empty shavings. The hose is at the back , about 6" up from the bottom and connected with a toilet flange. Works great as I am sure yours does.

Norm

Re: Powermatic guard bracket adapted to dust collector

#6

Re: Powermatic guard bracket adapted to dust colle

Dave Belser in NH

>Great idea using the lamp hood - I've got a couple kicking around that I will put to good use!

Dave

Re: Powermatic guard bracket adapted to dust collector

#7

Re: Powermatic guard bracket adapted to dust colle

jared

>I had a bunch of those old lamps kicking around for quite some time and finally found a use for it. My father used to farrow pigs about 40 years ago and had 20 sows each in their own pen with a heat lamp in one corner of the pen to keep the baby pigs warm. Even though the lamp had not been used for years I scrubbed it well to eliminate the smell of the hog house. Jared

Re: Powermatic guard bracket adapted to dust collector

#8

Dick Hines

Re: Powermatic guard bracket adapted to dust colle

Dick Hines

>I love the use of the duct tape. Duct tape, dry wall screws and ty-raps will fix almost everything.

Re: Powermatic guard bracket adapted to dust collector

#9

What I did

Rick Davenport

>Laziness is the mother of invention.

It's been set up for less than a week and I did have a tenon fail on a 8" holly bowl. It flew down instead of up so the guard didn't kick it back to me.

I just pull off the bungies to vacuum the lathe.

The clamped lamp is handy too.

Rick


img