Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Support WoodCentral when buying things you need

Power Buffing?

Posts

Power Buffing?

#1

Power Buffing?

David Hammond, in Powder Springs GA

>Hi guys:

I've got the Beal system and have enjoyed adding the sheen I can get from this high speed buffing, right off a bowl that I've sanded with Watco. But lately I've been experimenting with some water based laquer - I'm looking for clear, high gloss and a velvety feel. I attempted to put the laquer over Watco, which according to the manufacture should be possible. But, alas, when I tried to buff the laquer, beginnning with the Tripoli, the laquer buffed right off. So, I'm assuming I have an adhesion problem, one that Target Coatings says can be solved by simply using their water based compatible shellac/barrier coat. My real question is not about the adhesion, I can experiment well enough with that (although chime in if you guys know something I don't!) but about power buffing - can I buff a laquer finish, water based or solvent, with the high speed Beall system? If that's possible, will that attain the same kind of effect a hand rubbed laquer finish will - high gloss, and a smooth feel? I ask becuase I'm not 100% sure that adhesion was my problem, and becuase I didn't think the furniture building industry used such high speed buffing equipment, on a table top for example.

Any thoughts about achieving a smooth, glossy finish with some sort of power buffing equipment would be much appreciated!

Tia,

David

Re: Power Buffing?

#2

Re: Power Buffing?

john lucas

>David I don't buff at high speed with the Beal. I probably buff at 1000 rpm or less. I use a lot of lacquer. I don't put anything underneath it unless it's sanding sealer which I do rarely. Hight speed along with a lot of compound on the tripoli will eat the lacquer right off. I use the tripoli very sparingly on the wheel and slow speed.

Re: Power Buffing?

#3

Re: Power Buffing?

GeeSeaWhy

>I mostly use Formby's tung oil finish and that buffs out very nicely. I've had problems power-buffing shellac and General's polycrylic finish. Neither can take the heat and melt into a sticky mess. I haven't tried running as low as 1000 rpm though, generally I'm up around 1600-1800 rpm.

Graeme

Re: Power Buffing?

#4

Re: Power Buffing?

RussFairfield

>If the lacquer comes off in sheets or flakes, you have an adhesion problem. It it just comes off and disappears you have an abrasive problem, and you are most likely buffing with too much, too fast, and too soon.

Lacquer takes a long time for ALL of the solvents to evaporate. You should be waiting a week before buffing, 2-weeks is better, 3-weeks is better yet, and you will get the highest gloss if you wait until next year. Yup, lacquer doesn't totally dry to full hardness for 1-year in most conditions.

Shellac takes twice as long as lacquer, but has the advantage of being a High-Early finish that gets moore of its hardness within the early weeks and then tapers of to reach full hardness in 1-2 years. That gives Shellac the appearance of hardening up faster than lacquer which has a slow rate in the early days after it is applied.

Run the wheels at 900 RPM, use light pressure, and forget about the Tripoli compound unless you have an exceptionally rough surface. Sanding is important. Start with the White Diamond if at all possible. Tripoli is jewelwer-rouge, 800-grit, and it will remove a soft lacquer very quickly.

Re: Power Buffing?

#5

Ric Taylor

Re: Power Buffing?

Ric Taylor

>David,

Lacquer is a soft finish, and high-speed buffing will cut through it just like sandpaper would. You need to use low speed and a light touch. Don't use the tripoli on lacquer. I only use the white diamond, and a light touch at 700 rpm. Take your time, and it should polish up nicely.

Ric

Re: Power Buffing?

#6

Re: Power Buffing?

David Hammond, in Powder Springs GA

>Thanks guys! All of your posts have really helped me out. Now, on to the shop and more experimenting!

David

Re: Power Buffing?

#7

Re: Power Buffing?

RussFairfield

>David,

I have no idea why most people still believe that we have to use an oil finish under a lacquer. You don't. Lacquer does every bit as good a job of popping the grain by itself as using an oil finish under it. Sand to a finer grit, maybe 1200-1500 frit, before using the lacquer, and the grain will be brighter than you will ever see from an oil.

Re: Power Buffing?

#8

Re: Power Buffing?

John Lucas

>Russ there was a good article on this in one of the magazines I just got. I think it was Finewoodworking. They guy did a test on 3 different species of wood and 3 different finishes. His conclusion was, you don't need to put oil on first.

Re: Power Buffing?

#9

Re: Power Buffing?

RussFairfield

>Hell, I discovered that 40 years ago. I wonder what took the "experts" so long.

Re: Power Buffing?

#10

Re: Power Buffing?

David Hammond, in Powder Springs GA

>That's why I'm here Russ, and the rest of you - 40 years of experience is more valuable than most people will ever understand. I wasn't planning on using the oil all the time under the laquer, but if it will work I will just add that to my list of finishes in my repertoire - I think the oil on some woods might help give the piece a little more patina to start with, such as a cherry bowl. But, I'm just learning and I enjoy hearing from all of your experiences.

Thanks!

David

Re: Power Buffing?

#11

Re: Power Buffing?

RussFairfield

>There is nothing wrong with using a lacquer finish over an oil or varnish finish, but the oil has to be fully cured before applying the lacquer, and the surface has to be buffed with steel wool to give the lacquer something to adhere to.

Remember that 30-60 days that everyone has told you was necessary before an oil finish is food-safe. That's because it takes that long for the oil to fully cure and for all of the solvents to evaporate. That is the same 30-60 days that we should be waiting to put the lacquer over the oil. Let your nose be the judge. If you can smell it, it isn't done.

You can go at it sooner with a barrier coat of shellac. But, that isn't as easy as it sounds. The barrier has to be 100%, and that means application of the shellac and sanding it smooth without cutting through it, not an easy task.