Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Precision you can feel — woodworking perfected with Lee Valley

Riser Blocks??

Posts

Riser Blocks??

#1

Riser Blocks??

George (Oxford, NC)

>I want to raise the bed of my lathe about 5-6" to bring it to elbow height. I can use two 6" square blocks or four 2"x6" (one under each pair of mounting holes). The question is though, what to use to make these 6" tall. I am thinking of laminating 2x4 stock (four layers). Is pine too soft? Using 8/4 hardwood seems a waste of good 8/4 stock. Other suggestions?

George

Re: Riser Blocks??

#2

Re: Riser Blocks??

Gil Jones

>Eight pieces of 3/4" plywood glued into a block would be close (as they are not truly 3/4" anymore). It would be more stable than solid wood.

Re: Riser Blocks??

#3

Re: Riser Blocks??

Allen Neighbors

>George, I raised my old Grizzly 5 1/2 inches, by making a false bed, and putting it between the lathe bed and the legs. (The legs were already screwed to the floor, inside 5 gallon buckets filled with sand.) The false bed I made is from pine 2X6 laminated to 3/4 plywood. (Plywood is outside layer) Both ends and center crosspieces are made from pine 2X6 by themselves. Ply and pine is glued and screwed together, with holes bored to match bed and legs, just used longer grade 8 bolts. Sorry the pic isn't better. You could do the same by adding a 1/2 of ply to the bottom of the false bed to make it 6 inches instead of 5 1/2.

Just an alternate way of doing things. I guess it's my twisted mind.:o)

Anyway, I wouldn't waste hardwood, I think pine is fine.

Allen


img

Re: Riser Blocks??

#4

Dominic Greco's legs *LINK*

JKJ in East TN

>Dominic has a very nice article here on WC that includes risers for his lathe. He used pressure treated lumber due to the possibility of moisture.

JKJ


WC article

Re: Riser Blocks??

#5

Brad Vietje

Re: Concrete Blocks

Brad Vietje

>

Re: Riser Blocks??

#6

Re: Riser Blocks??

Fog Tanner

>I raised my "mini-lathe" (a 16" Delta steel bed) up to elbow height using 2 layers of pine 2x6s under each end. The legs are an inverted T, so the bottom layer is two pieces with a couple inches gap in the midddle to give me four feet. Works with no problem.

When I got my Vic300, I had to raise me up to elbow height. I made a floor out of the 2x12 crating laying on some 1x4 runners which works great for both height and my feet.

Re: Riser Blocks??

#7

End Grain

Phil Joines

>Make your blocks so the grain is vertical. End grain is almost uncompressible.

Re: Riser Blocks??

#8

Re: Riser Blocks??

Brian Hahn in SW Wisconsin

>Filling the box with sand will help reduce vibration. I did that with the stand I made for my Jet mini and it really helped.

Re: Riser Blocks??

#9

Re: Riser Blocks??

Bill Hale

>Allens way is the way I would go, but.

I would leave the side open and extend a shelf out a way to allow tools etc to be put under the ways. I would create a 5 sided box.

We all tend to lay our tools on the ways and the seem to end up on the floor point down. This will provide a place for a little storage.

Good turning and be safe

Bill in Casa Grande, AZ.