Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

REAL MILK PAINT

Rookie - Cutting Segments for Bowls/Urns?

Posts

Rookie - Cutting Segments for Bowls/Urns?

#1

Rookie - Cutting Segments for Bowls/Urns?

David Lykins - Marietta GA - guitardude

>I just started gluing up the segments for an Pet Urn I'm going to attempt to make/turn for my roommate. Once I started gluing up the segments I realized that for some reason they seem not top be a perfect 15 degree (30 degree both sides) cut. On several of the segments I got some small gaps and finally guled up half of the segments (half of the complete ring) and then sanded the joining half peices flat on my belt sander in order to join the peices.

I have this odd feeling that though my miter saw is set up correctly, the small peices of wood are moving slightly during the cut. I built a jig to clamp the peice down onto the table of the miter saw on the cutting side of the blade, but I still think its moving. When I measured the 15 degree angle the saw seemed to be right on, but the peices just didn't join up properly.

I've been using the trial program of WOODturner Pro, to determine the size of the individual peices. Very cool program in my humble opinion.

Any suggestions, ideas or jigs I could make to cut the segments more accurately?

Thanks for any help.

Re: Rookie - Cutting Segments for Bowls/Urns?

#2

Re: Rookie - Cutting Segments for Bowls/Urns?

John Lucas

>David I could measure all day long and never get them right. What I do is cut test pieces until I get the saw right and then cut them. Even then I might not nail it everytime. The quality of the blade, how fast you cut and probably the quality of the saw all come into play as well as holding the wood really well. John

Re: Rookie - Cutting Segments for Bowls/Urns?

#3

Re: Rookie - Cutting Segments for Bowls/Urns? *LINK*

Ron in Drums PA

>This book explains it well


http://www.tahoeturner.com/book.html

Re: Rookie - Cutting Segments for Bowls/Urns?

#4

Re: Rookie - Cutting Segments for Bowls/Urns? *LINK*

georgetroy

>First off your boards should be flat and true. No curves and wraps. You should have a zero clearance fence. A 1/4-1/2" board approx. 1 1/2 " high will work. I use a 1/4" piece of hardboard and just use double stick tape under clamp pressure. Use saw stops, a sharp saw blade. Chances are the degree setting is not spot on, bump until you get it right and tighten down. You check your rings by making your trail cuts and a band clamp. Hold the ring up to sunlight or a bright light, it is not correct until you see no daylight. I have a basic segmented turning site with instructions and drawings. GT


Segmented turning

Re: Rookie - Cutting Segments for Bowls/Urns?

#5

Keith Tompkins

Re: Rookie - Cutting Segments for Bowls/Urns?

Keith Tompkins

>David, one thing to consider: I assume you are cutting long pieces into the segments...be sure the pieces you are using are perfectly straight, and do not taper along the length. Example: 1/8" taper on a board will cause ALL kinds of problems, as you will be cutting two different angles as you flip the board for each new cut.

Re: Rookie - Cutting Segments for Bowls/Urns?

#6

Re: Rookie - Cutting Segments for Bowls/Urns?

Nick Tuzzolino

>Curt Theobald -www.curttheobald.com-has a DVD (DVD #1) that demonstrates, VERY clearly how to make a jig that will give you precise tight joints. I recently tried this system and IMHO is bulletproof. You need a 10 or 12 inch disc sander to make this work.

Re: Rookie - Cutting Segments for Bowls/Urns?

#7

I have this book,

Eddie Pacheco, Vacationing in Colorado

>I recently ordered this book and I will second that it is very informative and descriptive in its presentations and text. I also learned a lot, prior to geting this book, from George Troy's website.