Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Super Resolution Thermal Imaging Camera

Harbor Freight airbrush compressor - rec *LINK*

Posts

Harbor Freight airbrush compressor - rec *LINK*

#1

Harbor Freight airbrush compressor - rec *LINK*

Mike Schwing from Md.

>I am too cheap to pony up big bucks for a fancy pants Iwata or other top name airbrush compressor. Instead I have used my 5 gallon noisemaker pancake, with a moisture trap. But it is just too damned noisy, and that drives Mrs. Schwingding nuts as much as it does me. This also leads me to not want to airbrush anything, which is sad because it is a great skill to have in your toolbox.

I was about to pull the plug on a $300 Iwata model when I happened to think of Harbor Freight. After all, its not a daily use tool, yet, and Harbor Freight has a store nearby. So I went to the website (linked below) and lo and behold - I find one for $49! So I went and bought it.

It works great. It is extremely quiet - enough so that it can sit right next to me on the counter and not bother me one bit. It has a good moisture trap, and delivers a constant .7 cfm at 30PSI when under load, plenty enough for modest airbrush work of thin materials, but no way would it power a bigger gun. Totally portable, too. Only drawback is there's no pressure regulator on it, but I haven't found it necessary. For $49 I'd buy another one.

What I would NOT recommend however, is buying one of their airbrushes. God to DixieArt and get a good Badger, Paasche, or Iwata. But this is a nice, quiet, reliable compressor.




Harbor Freight Airbrush Compressor

Re: Harbor Freight airbrush compressor - rec *LINK*

#2

Re: Harbor Freight airbrush compressor - rec

Gerry Meekins

>Thanks for taking the time for the review Mike. I saw one of these guys in HF last time I was thru and started to pick one up. Their Airbrush looks like a kazoo with a inkwell attached to it! LOL

Gerry

Re: Harbor Freight airbrush compressor - rec *LINK*

#3

Re: Harbor Freight airbrush compressor - rec

Chris K in MD

>Mike,

Would this power my new powercrafter? I hate the noise for that too.

Re: Harbor Freight airbrush compressor - rec *LINK*

#4

Re: Harbor Freight airbrush compressor - rec

Mike Schwing from Md.

>Chris, I don't know for sure, doubt it, can't recall the CFM/PSI reqs for the Powercrafter, but I'll give it a shot for you.

Re: Harbor Freight airbrush compressor - rec *LINK*

#5

Re: Harbor Freight airbrush compressor - rec

Dick Anderson

>Chris:

The Power Crafter should have 40-42 psi compressor pressure. The HF compressor woud be a little under powered for the high speed rotary carver. Also, I believe you may want an air pressure tank to provide a more steady volume and pressure which isn't included with the HF unit.

Dick

Re: Harbor Freight airbrush compressor - rec *LINK*

#6

Re: Harbor Freight airbrush compressor - rec

eaglesc

>"Their Airbrush looks like a kazoo with a inkwell attached to it! LOL"

Don't knock it if you haven't tried it.

I bought it for $5.00 just to spray lacquer as Russ stated and I can attest it does that well.

Add up the cost of spray lacquer with lousy nozzles versus an adjustabler mist.

For pens it is an excellent buy.

I bought 2.

I use it with a HF compressor and regualor/separator

I use it for my pens.

The LOL is on you

Re: Harbor Freight airbrush compressor - rec *LINK*

#7

Re: Harbor Freight airbrush compressor - rec

Chris K in MD

>Thanks guys I was hopeful