Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Need a tree taken down or milled?

System Three Epoxy- 5 min

Posts

System Three Epoxy- 5 min

#1

System Three Epoxy- 5 min

Jill

>OK I probably have a few dumb questions but please remember I am a newbie turner. I have a grove around a bowl I want to fill in with colored epoxy. I have bought some Liquitex acrylic paint to mix in the epoxy. Sooooooooooo I did it on scrap (thank goodness) and I have found that after sanding with 320-400-600-1200, buffing with the Beal system and even trying Renisance wax nothing makes it shine. It is still dull. What do I need to do!?!?!!? I have read about a filler. What is that? I didn't see any such product with the system three. Is there a different epoxy I need to use or what? It appears as if it isn't hard. I can make a mark with a stick tho it heals itself. More hardner???? Yikes I am in a panic. Lesson 101 NEVER panic!!!! ;-) And...I thought the turning was tuff. '-)

Re: System Three Epoxy- 5 min

#2

Keith Tompkins

Re: System Three Epoxy- 5 min

Keith Tompkins

>Jill. try the regular epoxy, the five minute stuff doesn't harden up as well....seems to stay soft.

Re: System Three Epoxy- 5 min

#3

Re: System Three Epoxy- 5 min

Bill Grumbine (Kutztown PA)

>Hi Jill

Just to piggyback onto Keith's advice, a slower set epoxy will probably do better for you than the five minute stuff. The good news is, you just need to buy a different hardener. Hardeners are rated for different rates of curing. The slower you go, the harder it will probably be, although you may not notice a huge difference. You can use the resin you already have. System 3 should have several options on their website.

Bill

Re: System Three Epoxy- 5 min

#4

Re: System Three Epoxy-How about T-88? instead

Jill

>Thanks Keith and Bill. I am not sure I understand your answer. I looked on the System Three website I see a 15 min, 30 min etc.... Are you advising me to buy just the hardner for 15, 30 min? Or is there a better product for the purpose I am attempting to do? I see that there is a T-88 epoxy is this better and more appropriate for what I am attempting to do? I know absolutly nothing about epoxy so sorry for the questions but I really want to put this product on my bowl.

Thanks Jill

Re: System Three Epoxy- 5 min

#5

Re: System Three Epoxy-How about T-88? instead

Bill Grumbine (Kutztown PA)

>Hi Jill

Epoxy consists of two parts, the resin and the hardener. The resin for most uses is the same stuff, while it is the hardener that varies. Different hardeners are formulated to allow the epoxy to cure at different rates. Ambient temperature affects the rate of cure as well, and the various rates specified for each hardener are specified for a particular temperature. For example, the various rates you mention may be valid at 70 deg (I don't know if that is the actual temp, I am just making up numbers for illustration).

if you are working in a very hot environment, and you need time to assemble everything, or coat everything with the epoxy you are using, then you would choose a slow setting hardener. If you are working in a colder environment, you might want a faster setting hardener. Application of heat by shining an incandescent light on the piece can accelerate the cure. Generally the slower the set time, the stronger the bond. The differences between bond strengths for most of us are not going to be an issue, although as you are finding out, the fast set 5 minute stuff is not getting as hard as you would like. You should be able to buy a slower setting hardener and mix it with the resin you already have. So, instead of setting in 5 minutes, it may take 30 minutes. If you live in PA and turn the heat in the shop down to 40 deg at night like I do, it will take all night to set. But it will set properly, as long as you keep your mixing ratio accurate, which most of the time is two parts resin to one part hardener.

I hope this makes my first answer a little clearer for you, but if not, let me know. I learned all this stuff back in the late 90s when I was building a boat, and went through about five gallons of epoxy.

Bill

Re: System Three Epoxy- 5 min

#6

Re: System Three Epoxy- 5 min

Allen Neighbors

>I'm a newbie turner, also, but I've used a ton of epoxy. I use the stuff they sell at Wal-mart, simply because I haven't been anywhere that they sell System 3.

It could be that you are putting too much coloring medium into the epoxy. That will have an adverse effect on the hardening. The light bulb heat technique that Bill mentioned works very well to speed the hardening time. (I use the 60 minute type)..

my $.02.

Allen, praying for rain in Childress Texas.

Re: System Three Epoxy- 5 min

#7

Re: System Three Epoxy- 5 min

John Lucas

>Jill You might have two problems. Like Keith and Bill said I find that the 5 minute epoxy doesn't dry as hard. I like the stuff that takes at least an hour to dry or longer and I leave it 24 hours. When you mix things with epoxy it doesn't always act the same as plain epoxy. Also the quantity of non epoxy additive affects the curing time and hardness. You might try something else to color it. I've had very good luck with india ink.

Some epoxy companies have additive that you can put in that thickens the epoxy. The only one I've used is by West System. You can mix in the thickener until it's really thick like peanut butter. I've used powdered tempera paint and crushed up pastel chalk to color epoxy. It also acts as a thickener where the india ink leaves the epoxy just as thin as normal.

Re: System Three Epoxy- 5 min

#8

Re: System Three Epoxy- 5 min

Jill

>Thanks Guys for the added information - your the best. I feel so blessed to be able to run to my computer (after searching in my books, articles, etc)and ask this great group of woodturners for help. I think I will attempt to use West products and see what happens. I tried another science experiment(using System Three products) with less color and more hardner added and two days later it is still what I consider not hard enough to sand. I may give ink a try also tho I am shoting for a colbalt blue hue and have the paint color I am seeking. Happy Turning

Re: System Three Epoxy- 5 min

#9

Re: System Three Epoxy- 5 min

Mike Schwing from Md.

>Keith, if you're finding the 5 minute stuff to stay "soft", I suspect one of two things is occuring (maybe both). 1. inadequate mixing, 2. inadequate ratio of hardener:resin. It should finish up rock solid, but will not take a polish like CA.

Re: System Three Epoxy- 5 min

#10

Re: System Three Epoxy- 5 min

Bill Grumbine (Kutztown PA)

>Hi Jill

More hardener than what is called for will actually have the opposite effect! I have done a little tinting, added lots of fillers of various sorts from powder to wood dust to chips to silica, but the ratio of hardener to resin must be strictly maintained. Too much variation in either direction leaves the stuff soft no matter what.

Keep working at it though, it is worth learning the ins and outs of the stuff, and it does a real nice job on a lot of things.

Bill

Re: System Three Epoxy- 5 min

#11

Re: System Three Epoxy- 5 min

Fog Tanner

>I have used various epoxies for thirty years build model aircraft. I typically use three to four different epoxies in building a high performance raceplane. Five minute epoxy is not what you want for your application. It will always be a little soft, but not as soft as what you describe (your mix was either off or not enough cure time). If you want to get a glass finish, it will take a little patience. On my racing airplanes, I can get a glass slick surface with a mirror shine, and that is just the bare surface. I use epoxy finishing resin for the surface and paint over that. It does take some time though.

The times that you see on the epoxy is the "set" time or working time. 30 minute epoxy is not reay to use in 30 minutes, you just have about 30 minutes before it gels. The set times are also for smaller quantities, the larger the volume, the quicker the set time. You can also retart the pot life, by placing the mixing cup in a cup with ice in it. To reach full strength will take seven days. That is true for the 15,30,60,120 minute epoxy that you will normally buy. There are some specialized epoxies used in pattern making which have different set and cure times. The best epoxy I have is made by one of the large chemical companys for their internal use and is not sold commerically.

I use various epoxies for finishing and filling. But, I let them cure for a week before sanding or machining them. On wood turning, I fill the void, like a groove, proud of the surface and tool the surface, then follow it up with sanding. I normally use 3m silicon carbide wet or dry, used wet. I will go through grits starting with the highest I need up through around 800-1200. This will give a glass finish. If I am going to put a finish over the surface, I normally stop at 400 if using a film type finish, higher for oils. It does involve a lot of sanding, but the results are well worth it.