Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Good Hope Hardwoods - Walnut Slabs & Specialty Hardwood Lumber

bearing vaccuum adapter

Posts

bearing vaccuum adapter

#1

bearing vaccuum adapter

Rick in MI

>I built a rotery adapter like the one in wood turning design a few issues back and I can only draw 11" of mercury through my bearing. When I remove the hose from the adaptor I can draw 26". I have a Gast pump I picked up used and was wondering about the compasity. Called Gast and they said it runs 8 cfm, plenty. what bearing , #, is every one using. Thanks.

Re: bearing vaccuum adapter

#2

Better bearing...

Peter Teubel

>I have made many rotary adapters and I found that a water pump bearing provides the most leak-proof seal. The picture shows a typical water pump bearing (I use NSK# 885586...the shafts are longer on each end). After cutting the shaft(s) short (as the arrow shows) I drill a hole thru the shaft. Takes awhile because you're drilling thru more than 2" of steel (3/16" diameter is plenty).


img

Re: bearing vaccuum adapter

#3

Re: Better bearing...

tek-Brunswick, Ohio

>That is a good idea! Are those available at car parts stores and about how much do thay cost?

Tom

Re: bearing vaccuum adapter

#4

Re: bearing vaccuum adapter

Nelson

>After building 2 that really did not work that well I bought the Oneway rotary adapter and it works great, decided I like turning better than building gadgets and tools.

Re: bearing vaccuum adapter

#5

Re: bearing vaccuum adapter

John Lucas

>I guess I got lucky. I just went to the local bearing place and bought a sealed bearing. It was nothing special. It's worked fine for me for about 6 years now. In fact I bought another one to go with my mini lathe and it works just as good.

Re: bearing vaccuum adapter

#6

Leo Van Der Loo

Make sure it's a sealed not shielded bearing

Leo Van Der Loo

>

Re: bearing vaccuum adapter

#7

Re: Make sure it's a sealed not shielded bearing

Gerry Meekins in Maryland

>Like John, the bearing that I am using has sealed well for a couple of years. Nothing special about it, I think I paid about 3 or 4 bucks for it and I can draw 28" with it. I have had leaky drums that I've made from MDF. Usually a couple of coats of shellac or Mylands friction polish seals it right back up to the 28" mark.

Gerry

Re: bearing vaccuum adapter

#8

Re: Make sure it's a sealed not shielded bearing

Rick in MI

>I bought mine at an automotive parts store, it is double sealed. I guess I will try agian. thanks for all the responses.

Re: bearing vaccuum adapter

#9

Re: bearing vaccuum adapter - - quick test

Pete in Holland, MI

>Built a swivel for my JET 1236 a couple weeks back. Had the wrong bearing first time out. Was shielded only. Could only hold 8" of vacuum. The sealed bearing works fine though. 27" is obtainable on my system.

A quick test was discovered. Seal the bearing with your lips, put your finger in the ID to seal it up. Should be able to suck on it with no leakage. You'll know if you have a sealed or shielded bearing then.

Re: bearing vaccuum adapter

#10

Re: Can't you tell just by looking?

Al Crandall (NE of Indy)

>I'm certainly no expert on bearings, but I have built several rotary adapters with sealed bearings. All the sealed ones have had a rubber/plastic of some kind or other type of seal which looks quite different from metal. All shielded bearings I have noticed have had metal shields which look like metal.

Re: bearing vaccuum adapter

#11

Re: bearing vaccuum adapter

Fog Tanner

>There is an article I found on the net by Al Crandall about building an adapter. The bearing that was used came from Lowes and was an inexpensive water pump bearing, part number 99502-H .625 bore double seal for Ace Pump. It is in the "specialty fastener dept". I made the adapter, and used the same bearing from lowes, cost around $6. I later found a better bearing from a bearing supply house was $6.50. The one I have works great, can pull 26" with no leakage, so I have not bothered with the "higher dollar" bearing.

Re: bearing vaccuum adapter

#12

Re: Better bearing... *LINK*

Peter Teubel

>I order them from a local bearing supply house (Future Bearing Inc.) a few miles from me. They run about $15 each.


Future Bearings