Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Rare Exotic & Domestic Hardwoods, Milled In-House in Oregon. Browse Unique Stock.

Hand pieces for Wood Burners

Posts

Hand pieces for Wood Burners

#1

Hand pieces for Wood Burners

Mike Rubes, Apex, NC

>Hi all,

I'm really intrigued by the beautiful burned pieces people post here and I want to give it a go. I'm pretty much settled on the Burnmaster Hawk from Wood Carvers Supply, but am a bit confused about the different hand pieces available. I'd like to get just two for now and it seems like the tip 1A for general use and a 6A for writing would be a good start. Here's a link to their web site:


The Wood Burner


Here's a link to the first page listing the tips:


Tips Page

Any guidance on the tip types would be greatly appreciated.

I'd like to get one ordered in the next few days.

Thanks!

Mike

Looking to burn outside the fireplace in Apex, NC

Re: Hand pieces for Wood Burners

#2

More information

Mike Rubes, Apex, NC

>Hi all,

After I read my post, I realized I should have included a bit more about what I want to do with the burner as that might help dictate what type tips I would need :) I would like to be able to burn my signature in and to do some basic geometric designs for now. Some with curves and some with straight lines. I'm not that interested in shading areas yet, I figured I would start with outlines and see how that goes for now. I have some prisma color markers that I want to play with also as coloring for the shapes.

Thanks!

Mike

So many ideas, not enough time (or money!!) in Apex, NC

Re: Hand pieces for Wood Burners

#3

Re: More information

Molly Winton

>Hi Mike, the two pens I use the most are the 6A and 10A. I use the 10A for all of my outlining. It works great for straight and curved areas. I highly recommend getting a stone to sharpen it. It works best when very sharp. I also use this pen for signing. I find the 6A too blunt to get a crisp signature. I use my 6A for fill-in and stippling. I don't think I could work without these two primary pens. Have fun and experiment a lot with different heat settings and style of pen use. I used a board first to practice on to see how they would react, then prior to burning on a piece I used a scrap portion of the wood to test the heat setting. Every wood reacts differently to the heat settings, due to the density/pourosity(sp) of the wood.

Re: Hand pieces for Wood Burners

#4

Re: More information

Mike Rubes, Apex, NC

>Hi Molly,

Thanks for the quick reply. Just curious, but if I am reading the catalog correctly, you can either do a pen type that has the tip permanently attached or one with a replacable/interchangeable tip. Is that correct? Have you tried both and if so, do you like one system over the other?

If I can get 1 pen and multiple tips, seems like I could get more tips since they are less expensive than the pen/tip combo.

Thanks again for your help,

Mike

Trying to maximize my dollar in Apex, NC :)

Re: Hand pieces for Wood Burners

#5

Re: More information

Andi Wolfe

>Mike, the new replaceable tips system for Detail Master is sturdy enough that you could get this and try a lot of different trips for an economical price. 10A and 6A are my standard pens, but you might want to try the spear point one, too. You will definitely need to sharpen the 6A to make it usable for writing.

Re: Hand pieces for Wood Burners

#6

Re: More information

chris rolke

>i too have been looking at woodburners and i like the burnmaster unit but i would like to be able to make my own "brands" out of nichrome wire

but i really dont what i want to do other than that i see many things i would like to do but dont know where to start

Re: Hand pieces for Wood Burners

#7

Re: More information

Andi Wolfe

>I believe the burnmaster accepts tips from multiple manufacturers. Razortip has a "make your own tip" kit, which you could use for making brands.

Re: Hand pieces for Wood Burners

#8

What Andi said!

Molly Winton

>

Re: Hand pieces for Wood Burners

#9

Many Thanks!

Mike Rubes, Apex, NC

>Hi Molly and Andi,

Thank you both so much for your replies! This was just the sort of information I was looking for. I'll place my order later this morning for the burner and handset and get a few tips to play with.

Fun stuff!

Thanks again,

Mike

Need more shop time in Apex, NC!!

Re: Hand pieces for Wood Burners

#10

Re: Many Thanks!

chris rolke

>i have found a razertip create a pen handpiece

http://www.treelineusa.com/cgi-bin/shopper?preadd=action&key=196-0100

and here is a razertip single burner with pen

http://www.treelineusa.com/cgi-bin/shopper?preadd=action&key=196-2000

( comes witH a large skew)

so now i am even more confused on what to do