Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Price drop on over 1300 Rockler items

Not getting sharpness I would like!

Posts

Not getting sharpness I would like!

#1

Not getting sharpness I would like!

Royce Meritt

>I have the Delta model GR250 variable speed grinder and the Wolverine grinding jig and Vari-Grind attachment. This set up has improved my sharpening considerably. However, I still do not seem to be getting the quality of sharpness to my lathe tools as I would like.

First of all, what do any of you recommend as far as grinding wheels are concerned? Secondly, what type of stone (or other implement) for honing? And thirdly, any particular tips to help me get the most out this set up? Thanks.

__________________

If fishing is a sport I MUST be an athlete!"

Re: Not getting sharpness I would like!

#2

JL

Re: Not getting sharpness I would like!

JL

>Honing works for me, though I have taken the tool from the wheel to the work often. That and a fairly reasonable stone. Have you honed or tried honing the inside once in a while? There are "two sides" to every cutting tool. If one side is nice and clean while the other isn't.... My $0.02.

Re: Not getting sharpness I would like!

#3

JL

Re: Not getting sharpness I would like!

JL

>BTW - for honing the insides I have a set of slip stones through 4000 grit (they weren't bought for turning tools). For honing the outsides, I use my Tormek honing wheel. When I have been at other locations, I have used a leather strop on a paddle charged with honing compound. The "fine" compound works quite nicely.

Re: Not getting sharpness I would like!

#4

Re: Not getting sharpness I would like!

John Lucas

>Royce First off the wolverine jig isn't perfect. You still have to carefully grind the edge until you see sparks come over the edge and you also have to control the grind so the edge is shaped properly. That's what I do 99 percent of the time and have tools that work great for me. Occasionally I hone the inside to get rid of the burr and if I'm really having trouble on so crummy wood I will hone the outside as well.

I use 100 grit wheels but I'm going back to 60 grit when these wear out. I seldom need them sharper than a 60 grit wheel will get them and with a 100 grit wheel if you miss the bevel just a hair on the grinder then it takes forever to regrind the edge. With a 60 even that faux pa is taken care of quickly. I've been asking around a lot and most turners I know have been using 60,80 or100 with 60 or 80 being the majority.

Re: Not getting sharpness I would like!

#5

Re: Not getting sharpness I would like!

Vicmarc.fan

>I have the same grinder but have made some modifications to it. The wheels were junk so replaced them with 120 and 60 white wheels. I don't like these wheels either. They are too soft but were not expensive. When they are gone I will replace them with ceramic wheels. I also installed Oneways balancing kit. Thing runs smooth enough now to balance a nickel on it.

I have had a Tormek for a long time and got in a habit of using a marker to make sure the arm is set right for your bevel. If off the marker is not removed all the way across. Make sure the bar is clamped down when you test because the Wolverine is so sloppy the jig moves up when tightned. Seems like a hassle but you can tell if the wheel is touching the bevel for sure.

Re: Not getting sharpness I would like!

#6

Keith Tompkins

Re: Not getting sharpness I would like!

Keith Tompkins

>Hi Royce, turn the speed up as high as possible, and take a light cut...you didn't mention the type of steel you are grinding.

The higher the speed, the finer the cut. Don't bear down on the tool while grinding. I am one of the few who recommend higher speeds while grinding.

Re: Not getting sharpness I would like!

#7

Re: Not getting sharpness I would like!

Jake Niedling

>Royce - I usually never hone my gouges, inside or out. I use the wolervine jig with 100 grit white wheel. Russ and Keith made some very good points regarding light touch on the grinder, type of steel and watching for the sparks over the edge of the tool.

You did not mention whether the tool bounces on the wheel when you try to grind. Don't forget to use a tool to clean the wheels and true them up round. The tool should not bounce when you put the tool against the wheel. With a good running & chlean wheel, HSS tool and light touch using the wolverine jig should produce a great edge.

Re: Not getting sharpness I would like!

#8

Re: Not getting sharpness I would like! *LINK*

Bob Fawcett

>I am brand new to turning, but not to sharpening. Here is a great article on grinding wheels.

http://www.woodcentral.com/cgi-bin/readarticle.pl?dir=handtools&file=articles_558.shtml

I have been using one of those folding DMT diamond hones. Mine is red and green and is 600 / 1200 grit. You can use it like a file to touch up the edge. I also have a round rod that has diamonds embeded. This is good for inside of gouges. Just enough to remove the burr.

You can get a felt wheel to install on your grinder and use green compound to hone the edge. These come in various hardness. Get a medium or hard so you don't round over the edge.


Grinding Wheels

Re: Not getting sharpness I would like!

#9

Re: Not getting sharpness I would like!

Barry Turner

>I'm not sure what wheels your grinder came with, but I can do pretty well with a pink 60 grit wheel from Woodcraft and the white 120 grit wheel that came with my grinder. It's a Delta slo-speed grinder.... the heavy one, weighs about 90#.

Re: Not getting sharpness I would like!

#10

Re: Not getting sharpness I would like!

Royce Meritt

>Thanks everyone. Some good suggestions here. I'll take all of your advice and keep working at it.

Re: Not getting sharpness I would like!

#11

Re: Not getting sharpness I would like!

Bill Hale

>Shape on the grinder and sharpen on a Tormek.

The Tormek light cut will lengthen the life of your tools an in my mind will pay for itself.