Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Rare Exotic & Domestic Hardwoods, Milled In-House in Oregon. Browse Unique Stock.

Craft Supplies "Apprentice" = PSI Barracuda 2? *LINK*

Posts

Craft Supplies "Apprentice" = PSI Barracuda 2? *LINK*

#1

Craft Supplies "Apprentice" = PSI Barracuda 2? *LINK*

Craig Daymon

>Wandering around the Craft Supplies site and saw the new(?) "Apprentice" chuck for $159.99. Looks like the same thing as the Barracuda 2 that Penn State Industries is selling. (I didn't read too closely, but it does come with several jaws and a case like the Barracuda 2.) This one appears to be in stock. Anyone have any insight into this one? Is it any good? It really looks like a close match to the Barracuda 2.

-Craig


Craft Supplies "Apprentice" chuck

Re: Craft Supplies "Apprentice" = PSI Barracuda 2? *LINK*

#2

Re: Craft Supplies "Apprentice" = PSI Barracuda 2?

Ron McKinley

>I have an Apprentice coming tomorrow. Tried to get the Barracuda2 from PSI but it's always on backorder so ordered the Apprentice from Craft Supplies and they shipped it right out. I'm sure it's the same chuck. Craft Supplies probably gets them from PSI since they are one of the biggest tool importers/suppliers in the country.....Ron

"A turning a day keeps the doctor away!"

Re: Craft Supplies "Apprentice" = PSI Barracuda 2? *LINK*

#3

Brad Vietje

Please let us know your impressions...

Brad Vietje

>

Re: Craft Supplies "Apprentice" = PSI Barracuda 2? *LINK*

#4

Apprentice Just Came

Ron McKinley

>Just got it a few minutes ago, opened it and it looks identical to the Barracuda2. Also got the Cole Jaws to go with it. Unfortunately I can't try it out right now as I've got a meeting to go to this evening. First thing in the morning will try it out and let you know what I think......Ron

"A turning a day keeps the doctor away!".

Re: Craft Supplies "Apprentice" = PSI Barracuda 2? *LINK*

#5

Thanks Ron. Look forward to hearing what you think

Craig Daymon

>

Re: Craft Supplies "Apprentice" = PSI Barracuda 2? *LINK*

#6

Tried it today!

Ron McKinley

>I put the Apprentice Chuck through the paces today. I tried every set of jaws and all of them worked perfectly. I had some pieces I had turned earlier and either didn't like or in one case the flange broke off a redwood twig pot.

I started with the twig pot (about 6" high) and chucked it in the flat or Cole jaws and it held it fine while I turned the broken flange away.

Then a 5" bowl of tiger-stripe eucalyptus that I didn't like the base so put that in the flat jaws/Cole jaws and made the base look a lot better. The flat jaws/Cole jaws are optional and don't come with the set. They work fine but wish they were a little bigger so I could use the full capacity of the Jet 10" Midi lathe. It will clamp about 5 1/8" in compression mode.

Then I switched to a redwood goblet I had turned and screwed up months ago and using the #1 jaws held it in the expansion mode and re-turned it. Now I like it. Then to a coaster blank. I had made my wife some candle bases for Christmas presents out of cherry and had one left over so I chucked one in the pin jaws in the expansion mode and now she has another one!

There was one thing about the chuck that concerned me. It doesn't have a back on the headstock end. It's open and you can see the gearing inside. I called Craft Supplies to see if I was missing a part and they said, no, that's the way they're made. He also said the Axminster Chucks are made the same way. He said just blow it out occasionally.

After turning all day there was very little dust/chips inside and it blew out with no problem. All in all, I like this chuck, especially all the different jaws that come with it. I do a lot of small work so the small jaws come in really handy.

The fit and finish is as good or better as my Nova Midi or any other chuck I've seen. Just one other little nit: it only comes with 8 screws for the jaws and I'm always dropping screws, etc. into the sawdust never to be seen again. My Nova Midi came with a few extra screws.........Ron

"A Turning a day keeps the doctor away!"

Re: Craft Supplies "Apprentice" = PSI Barracuda 2? *LINK*

#7

Thanks Ron, sounds like a good chuch at a good $.

Craig Daymon

>