Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Find a woodworking club near you

What tool\cut combination do you use on...

Posts

What tool\cut combination do you use on...

#1

Steven Antonucci

What tool\cut combination do you use on...

steve antonucci

>a face-grain platter?

I'm turning a large platter (17") in bloodwood (mini-gloat!) and I've been looking for a combo that has the minimum chatter/tearout and get a flat surface. Right now, my best combo has been a bowl gouge with the flute turned to 9 o'clock pulling from the center out, but I think there's got to be a better way...

Post the platter when I'm done- it's going to be be something special...

Steve

Re: What tool\cut combination do you use on...

#2

What tool ?

ob obrien In Pensacola

>Steve; I'd approach it from the rim to the center. Work the rim down close to the thickness you want and gradually work your way to the center. This will reduce the weight at the outer circumference and help get rid of the chatter. Ride the bevel. Sharpen again and take a very light finish cut. If your going for a real thin platter you might also want to stabilize the rim with your fingers. Hope this helps. OB

Re: What tool\cut combination do you use on...

#3

Be careful......

T Daniel

>the only fatality I know of from turning was when a high school student was turning a thin platter and it exploded. A piece of it was thin enough to cut like a knife and it hit him in the neck, severing an artery. Stay out of "the line of fire" and measure often.

TD

Re: What tool\cut combination do you use on...

#4

Re: What tool ?

Wally Dickerman in Arizona

>I would add, that before removing much wood from the center portion of the platter, you should complete the rim. If you plan on grooves, beads, etc. that should be done before removing wood from the rest of the platter. As you progress toward the center, the rim will go out of round enough so that you can't go back to it.

Wally

Re: What tool\cut combination do you use on...

#5

Re: What tool ?

John Lucas

>I would agree with the other two wholeheartedly. I use a bowl gouge ground like Stewart Batty does with a 40 degree grind through out. I used to use my standard bowl gouge with 65 degree grind and wings but I'm liking the Stewart Batty grind more and more especially for platters.

Re: What tool\cut combination do you use on...

#6

Re: What tool\cut combination do you use on...

Ken Grunke from SW WI

>I don't turn a lot of platters but if I did, I'd want a tool specifically for the purpose. I have a harder time turning a long, broad curve than a tighter curve of a bowl, for example. A gouge with a longer and/or thicker bevel than normal would help guide the cut better, like the body of a hand plane. And it would have a swept-back edge, giving a nice shearing cut from rim to center. A polished, nick-free toolrest is important also as you have to slide the gouge along it for such a broad curve.

I don't have such a dedicated tool, so I end up using a pad sander to straighten out the little irregularities.

Re: What tool\cut combination do you use on...

#7

Re:Once the rim is shaped, ...

JamieDonaldson

>.... the most important tool for a flat bottom is a straightedge that can show the terrain as you work toward the center. And don't powersand waves in it either!

Re: What tool\cut combination do you use on...

#8

Yes to the 3 above

Mike Schwing from Md.

>Only 2 differences for me. Rarely do I ever approach a platter with anything other than the Ellsworth signature gouge - other than to create a bead. I use the gouge in "slicing" mode, tip up at 10:30 o'clock, handle way down, toolrest down. Bevel rubs, cutting edge is at about 65 degrees from horizontal.

The other difference is that I will support the backside with a bowl steady for less chatter/movement. This is a delicate balancing act though, as at some point it'll still typically become warped enough that the steady rest causes more bounce than it calms.

Re: What tool\cut combination do you use on...

#9

Curves.....

Wally Dickerman in Arizona

>Steve, a bit about design. I'm very big on curves in my turning. I think that a curved surface is more pleasing to the eye and hand than a flat surface. I always see that the rim is either concave or convex rather than flat. Doesn't take much. I also like to see the inside bottom curved all the way to the center. No flat spots. Use a short straight edge to check it.

Wally