Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

REAL MILK PAINT

Another Improvement for my Nova DVR

Posts

Another Improvement for my Nova DVR

#1

Another Improvement for my Nova DVR

Barry Irby

>Along the lines of a weekend accomplishment, I made another improvement for my DVR. I mainly turn bowls and end up removing the tail stock frequently to avoid "turner's elbow" or to get it out of the way for coring or whatever. I have been removing it and laying on the floor. I end up picking it up and reinstalling it frequently. Much fiddling around.

Over the weekend, I made what amounts to a pivoting bed extension to park it on. I took a scrap of walnut and cut it five inches long and added some scrap aluminum angles I have been hording for years. I bought a bolt a the Borg and drilled a hole through it that matches one of the holes in the end of the bed. Epoxied the angles on and added screws for additional strength. Now, I can slide the tail-stock back onto the holder, lock it and tip it to the rear where it will lay down out of the way. Then just tip it back upright and slide it back onto the ways. Seems to work well. I was talking to someone about this and they tell me someone is making a lathe with such an accessory already in place. And I thought I invented this. All my best ideas were stolen by those who came before.

Re: Another Improvement for my Nova DVR

#2

Re: We both re-invented it.

Al Crandall (NE of Indy)

>I made the same thing for my PM4224 and took it to the show and tell of our club last July. The club secretary shot pictures of it and posted it on the club's web site. When I went to the KC symposium later in July I saw the lathe with the same feature I had built for my lathe. It is also pictured in the Tips page of the last AAW Journal, American Woodturner. I'm thinking of inventing a deep fried round flaky pastry with a hole in the center. Think it might sell?

Re: Another Improvement for my Nova DVR

#3

Re: We both re-invented it.

Barry Irby

>I have invented a number of things that have failed to make me rich. One was the Fishsicle. A piece of frozen fish on a stick. Drop it in the deep fat fryer and fry that baby up. A little Tartar sauce, a few hush puppies and you are on your way. Also thought of the Salad On a Stick. As you can tell, I probably eat too much fast food. I did think the Salad idea was perfect for McD's, but they were not interested. I think they stole that idea and changed it to the salad in a cup. A lot of good it did them. This stuff really should be customer driven.

Re: Another Improvement for my Nova DVR

#4

Re: Another Improvement for my Nova DVR

Dick Parr

>Barry can you post a picture of you extension. It sounds like just the ticket for my DVR as I have the same problem.

Thanks

Dick

Re: Another Improvement for my Nova DVR

#5

Re: Another Improvement for my Nova DVR

Colin Spencer

>Photo for me too please. I have the same problem.

Re: Another Improvement for my Nova DVR

#6

Robust Lathes...

Peter Teubel

>They have that (patented) tilt-away tailstock, but its a $795 option!

Re: Another Improvement for my Nova DVR

#7

Re: We both re-invented it.

Mike Brazeau

>Al - can you post the link to that site or possibly link the picture to a posting here. I saw the article in TAW and every time I lift the tailstock off my 2436 I think of it. I would use my outboard extension more often if I had one.

Thanks, Mike

Re: Another Improvement for my Nova DVR

#8

Parking place

Barry Irby

>Here are pictures with the tail stock sitting on the bed, waiting to be parked and a second one with it parked. Parking and unparking is a one hand operation. There is a bolt through the block, an ordinary 3/8 inch bolt with a nut that has a nylon piece captured in it to keep it snug. I ran the bolt though one of the existing holes in the end of the bed. The hole was threaded for one of the bolts for the bed extension, and if I were "smart" I would have looked up that hole size and threads and bought a bolt that fit it, but right off hand I don't know where to buy a metric bolt six inches (15cm?) long. Especially on Sunday when I'm doing this. Anyway, this works very well.


img

Re: Another Improvement for my Nova DVR

#9

Parked,

Barry Irby

>The underside had to have a radius on the rear bottom corner to allow the block to roll over to the rear. I also rabbeted the bottom front corner so that I can slide a locking plate into the bed of the lathe for something like a hollowing system or a bowl steady.


img

Re: Another Improvement for my Nova DVR

#10

Here's a link to... *LINK*

Paul in Phoenix, AZ

>...Robust Wood Lathes


Robust Wood Lathes

Re: Another Improvement for my Nova DVR

#11

Re: Parked,

Chris K in MD

>Nice Job Bary!

Re: Another Improvement for my Nova DVR

#12

Re: url for pictures.

Al Crandall (NE of Indy)

>http://www.cicaaw.org/image/tid/104

Sorry, I don't know how to make it an active link. This is the Central Indiana Chapter's web page. There are five pictures on this page and one on page two. Click on the pictures to enlarge them and you will see a brief note I wrote about what is being shown in each picture. I think the pictures and a little imagination will get you going. The agreement with the AAW which I signed is that I am supposed to acknowledge their co-ownership of the copyright when I referrence this item.