Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Reach the woodworkers who ACTUALLY BUY

Getting drilled on the lathe

Posts

Getting drilled on the lathe

#1

Getting drilled on the lathe

David Breth

>I had my first chance to use a jacobs chuck on the lathe. Don't know how I had the stones to keep trying after the mishap.

Basically, I was using an inappropriate drill bit, such that when it hit imperfection in the wood, or a certain amount of resistance, or whatever, it bit and held the wood, meaning that the bit was no longer "stationary", but being spun by the lathe because it was stuck in the wood. It got exciting very fast, as it always does with a lathe.

My thumb got smacked by the first revolution of the wheel (that lives on the tail stock, which I was using to move the bit into the wood). Fortunately, it didn't have full momentum at the time. I got away with effectively a slap on the proverbial wrist (thumb), and I'm lucky I didn't break it.

The revolutions were basically unscrewing the tailstock and stuck bit from the turning. So, at a high rate of speed, the tailstock housing was traveling away from the turning, and therefore creating more opportunity for wobble and explosions. I raced across the back of the lathe so I could reach over the (encased) motor to shut it off (ie., I did not reach over the work). I fully expected everything on the lathe - hardware and wood - to blow up all over me. Very scary moment. I was torn between hitting the deck and trying to shut it off. I made my choice, and that was that.

I did ultimately have success, however. When I reset everything, this time I held the jacobs chuck with my right hand while I turned the wheel with my left hand to drive the bit into the wood, and I advanced the bit very slowly. As it turned out, there was very little resistance this time, even with the wrong bit type. Previously, there was nothing to keep the jacobs chuck from spinning given basically any amount of resistance - the first time the bit hit something it didn't like, and it dug a little, the chuck moved with it, that allowed the bit to stay anchored, and that started the dominoes.

I'm doubtful that my "successful" method of holding the chuck was a good thing to do, which is part of the reason I'm writing this. First is to share a mishap, second is to understand how I should perform this operation.

Embarassing? You better believe it. But I'd rather bite the pride to learn how to do this and to help others avoid it.

I'll be lucky if I survive my learning curve...

David B.

Re: Getting drilled on the lathe

#2

Re: Getting drilled on the lathe

Jorge Castaneda

>David,

I cannot visualize how you hold the Jacobs with your right hand and advance the quill with your left, if your lathe is like all the lathes I know, the head stock is on the left and tail stock on the right, so the usual stance is to hold firmly the Jacobs with your left hand and advance the quill with your right. That is how I do it and never had a mishap, Also, if the tail stock was moving away it was not tightened properly.

Jorge

Re: Getting drilled on the lathe

#3

Re: Getting drilled on the lathe

Carole Valentine

>What kind of lathe do you have? I cannot for the life of me picture what you are describing here! Was your tailstock locked down?

Re: Getting drilled on the lathe

#4

Re: Something's not right here, David.

Al Crandall (NE of Indy)

>Please fill in the missing details for us. You mention "using an inappropriate drill bit". Most bits I have experience with are appropriate for use on the lathe. These include spade, twist, brad point twist, forstner, and gun drill bits with air blowing through them instead of oil. What style of bit were you using which caused this grief?

"My thumb got smacked by the first revolution of the wheel..." This should not be possible. No tailstock spindle should ever rotate inside the casting. There should be some mechanism to key it and prevent rotation. Tell us what brand of lathe you have, because this is an unsafe condition you are exposed to.

"the tailstock housing was traveling away from the turning"... Obviously the tailstock clamp didn't hold, or it wasn't tightened in the first place. You must secure the tailstock in place prior to drilling. If it won't withstand the pressure of drilling without slipping, you should consider a modification to the clamping plate beneath the lathe ways to allow the tailstock to clamp up tighter. The most common mishap when drilling is for the morse taper to let loose and then the chuck spins inside the tailstock. It's not particularly dangerous, but it is very hard on the machined surfaces of the taper arbor and the bore of the tailstock. I don't remember ever having a chuck spin on me in the tailstock of a metal lathe, but I know it happens in wood lathes. I'm still trying to figure that one out. Anyway, give us a little more info so we can help you to avoid a repeat of this incident.

Re: Getting drilled on the lathe

#5

Re: Getting drilled on the lathe

Jim Pugh, Ohio

>Others have asked good questions for which we are all awaiting answers. In the meantime, I'll ask another one. How fast was your lathe going when you were trying to drill?? For some reason a lot of folks seem to think they can drill at 2000 rpm and wonder why their drill bit burns up. Anyway, use the slowest speed you have on a non-variable speed unit and around 300-400 rpm on the rest.

Re: Getting drilled on the lathe

#6

Re: Getting drilled on the lathe

David Breth

>I haven't read the other responses yet, but wanted to give you a couple of quick notes to help you understand my position. If standing in front of the lathe at typical position is 6 o'clock, I was pretty much standing at about 2 o'clock, mainly because I wanted to be out of the path of anything that might go sailing off. That's why I ended up using opposite hands.

Also - yeah, that #$$#% tailstock does move a little bit from time to time. I hunker it down about as hard as I can, but have to keep an eye on it.

Re: Getting drilled on the lathe

#7

Re: Something's not right here, David.

David Breth

>I'm not good with knowing the names of one type of drill bit over another, but it was in the spade family. This particular one only had a blade on one side. I think the point/toe of the blade's outer-edge is what got caught.

The lathe is a Fische. It is difficult to explain precisely what happened there I'm afraid, and I may have to go look at the mechanism to understand it better. The bit got caught, which spun the jacobs, and I would have expected it to spin in the morse taper - in fact, it had spun earlier when I was putting the bit in. Possibly there was a lubrication problem, possibly there was an area inside the morse that allowed the male part of the morse to catch - I really don't know. It took the spindle wheel a few seconds to catch up to the revolution speed of the lathe, but once it did, boy did it ever go. The effect was that the "insert" of the tailstock, extended out of the tailstock, ala what it would do if you were turning the spindle wheel to extend it, but it did this very fast, and the result was to push the tailstock down the ways. As I write this, I'm realizing that the orientation of the "insert" is different now in the tailstock - som something may have busted in the process.

No, that tailstock did not clamp well. I've seen other lathes that had to be monitored for tailstock movement, so I didn't think to much of it, but maybe I can make an adjustment to the clamp.

Re: Getting drilled on the lathe

#8

Re: Getting drilled on the lathe

David Breth

>Off the top of my head, I think 1200. Slowest speed is around 600 - I realized that one after the fact.

David B.

Re: Getting drilled on the lathe

#9

Re: Getting drilled on the lathe

Ken Grunke from SW WI

>It's important to clear out the chips often, on just about any kind of drill bit. Someone else said the tailstock should be locked down--when drilling a hole, I often don't lock the tailstock except when starting the hole. Then I unlock it and carefully push it in by hand, so I can easily back it out to clear the chips, and back in again with firm downward pressure on the tailstock to keep it down on the lathe bed. This works good as long as the drill is started on center, which relies on the tailstock itself being accurately aligned with the headstock.

Re: Getting drilled on the lathe

#10

Re: Getting drilled on the lathe

David Breth

>I think I've got it figured out - but first - Ken - I experimented with this, but my tailstock doesn't move smoothly enough on the ways for me to do that. I keep it clean and do wax it from time to time, I think this is just a situation where I'm not working with a jet mini, I'm working with a substitute Jet Mini and that's kind of what you get in the way of ways.

Now, on to what it looks like happened. It looks like I did not have the locking arm engaged in the spindle of the tailstock. I experimented with this tonight, as I previously did not understand how that mechanism works. Now I get it - the locking arm screw slots into the keyed part of the spindle, so it can't spin inside the tail stock - got it. There is another mechanical element here that needs monitoring, in that the locking arm screw needs to be tightened or loosened very slightly depending on which end of the spindle you are engaging. I'm sure I had it in a fully non-engaged position, because the spindle screwed back and forth with less resistance that way. When the bit caught in the wood, the safety feature to prevent the spinning was therefore out of play.

The tailstock itself did start sliding down the ways when the mishap occurred, so I need to adjust that as well. But the big thing (in avoiding a repeat) is that I now understand the keyed element of the tailstock spindle. Seems obvious now, but it didn't register in any way to me before this evening.

Thanks very much for your helpful responses. Your questions took me right to the source, and I appreciate it!

David B.

Re: Getting drilled on the lathe

#11

Is this what you were using? *LINK*

Phil Joines

>I don't know how one of these would work on a lathe. You'd think the threaded point would pull it into the wood faster than faster than is safe.


img

Adjustable Wood Bit

Re: Getting drilled on the lathe

#12

Re: Is this what you were using?

David Breth

>I didn't start with that bit, I actually used a traditional whatever drill bit, but was unable to go deep enough, so I swapped out to what you pictured.

I agree with your point about the tip. That's why I called it inappropriate (that and the possibility that the outboard edge can catch). Though I will say that when I held the jacob's chuck (after the mishap), it worked very well.

David B.

Re: Getting drilled on the lathe

#13

Re: And don't wax...

JamieDonaldson

>...the bed ways and expect the tailstock to lock down securely , especially on a mini-lathe.