Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Abingdon, VA – Tree Cutting & Portable Sawmill

Bandsaw, safety opinons???

Posts

Bandsaw, safety opinons???

#1

Bandsaw, safety opinons???

Stuart Johnson

>A while back I was advised it was safe to saw through a round as long as the leading edge was supported with a small strip like the attached photo shows.

What are the expert opinions? The craftsman that demonstrated this is professional woodworker, teacher and author and a friend. I haven't had the need to give it a try but it did work very well when he demo'ed it. I don't remember if he used a scrap on the trailing edge but I don't think he did.


img

Re: Bandsaw, safety opinons???

#2

Re: Bandsaw, safety opinons???

Dick Anderson

>I take a section of 2x4, cut it lengthwise at a 45-degree angle then glue the two pieces onto a piece of plyood to form a 90-degree notch (cradle). I can either cut through the plywood and 2x4 cradle or if I wish to square up the end then cut though the log just off the end of the cradle.

Re: Bandsaw, safety opinons???

#3

exactly the way to go

Ed Kelle

>Much safer supporting it on both sides. I made my sled adjustable with sets of holes for the rear brace and I have mine running in the mitre slot.

here's a visual for you

stay safe and keep your hands and body on the sled side while working


img

Re: Bandsaw, safety opinons???

#4

Re: Bandsaw, safety opinons???

Mike Schwing from Md.

>While I'm not an "expert"....Do-able, yeah. Safe, not in my shop! I've had a bandsaw slice through a finger, if that thing started to roll on you, bind, and twist, who knows where that blade would wind up. Some of that bark thats grabbing that little strip starts to give out, you have a scary situation on your hands.

Re: Bandsaw, safety opinons???

#5

Keith Tompkins

Re: Bandsaw, safety opinons???

Keith Tompkins

>Stuart, your photo shows two pieces, a round, and a half round.

First, to cut the half round piece, lay it down on the flat surface. There is no need to have it standing up. A risky cut for no reason.

I don't like the strip of wood, it's not secure enough. The log could still roll over the strip, making the situation worse than if the strip wasn't used. If I HAD to cut this on the bandsaw, I think I would rather rip it down the center, supporting it in a v-grooved block.

Re: Bandsaw, safety opinons???

#6

two pieces

JKJ

>>...Stuart, your photo shows two pieces, a round, and a half round.

I think the two photos are of the same round piece of wood from slightly different points of view; the photo on the right is cropped, cutting off half of the round.

What I do is brace the round with the corner offcuts from cutting bowl blanks from square stock. I always seem to have plenty of these around. I read once that someone hot-glued such scrap pieces to his round before making the cut.

JKJ

Re: Bandsaw, safety opinons???

#7

that was probably me

Mike Schwing from Md.

>I've done that many times. I think I posted about it here. I always have long 2x1s in the shop. I just glue one on each side and then it becomes perfectly safe to make this cut.

Re: Bandsaw, safety opinons???

#8

Re: exactly the way to go

dick mc neill

>This is a good jig for cutting ends of round logs. Is there a jig that can safely cut down the center of a round log on a bandsaw?

Re: Bandsaw, safety opinons???

#9

Re: exactly the way to go

JKJ

>>...Is there a jig that can safely cut down the

>center of a round log on a bandsaw?

Dick,

I've seen two, but at the moment I can't get to the URLs. One is a sled with a large v-grove fastened to a board, with a saw cut down the middle.

The other is more versitile: a sliding jig with a long clamp fastened horizontally to one side. The clamp grips the ends of a short log and the whole thing slids along the fence. You can safely cut down the middle or even near the edge of the log if the clamp is tight enough, although I'd probably add some scrap under the unsupported edge.

JKJ

Re: Bandsaw, safety opinons???

#10

possibly

Ed Kelle

>I'd say mount the 45� blocks running parallel to the blade on some plywood, have the mitre runner set so that the blade cuts in the center of the blocks, put a stopper block to the rear to hold the log in place. As long as you don't cut the whole thing in half should be able to reuse it again. The only issue might be that the pith is not always centered on the log, so it would be tricky to get balanced grain.

I just usually rip on a chainsaw for this reason, and even then I do not get it perfect.

Re: Bandsaw, safety opinons???

#11

Re: Bandsaw, safety opinons???

Stuart Johnson

>Both the same piece just different angles. I would rather use the chainsaw but was wondering about the safety. I like the idea of a sled like Ed posted.

Re: Bandsaw, safety opinons???

#12

Re: Bandsaw, safety opinons???

bill dotten

>on lenghtwise parting - I tend to split the log in order to follow the pith. The parted halves can then be dealt with as they present themselves-

Bill Dotten