Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Find a woodworking club near you

Scorpion

Posts

Scorpion

#1

Scorpion

W.C. Turner

>What is the largest, & smallest vessels, that can be turned with the Don Pencil's Scorpion hollowing tools?

Thanks

Re: Scorpion

#2

Don Pencil

Re: Scorpion

Don Pencil

>The design was for approximately 12 to 14 inches in depth and 8 to 10 inches in width. The opening has about a 1 1/4" minimum diameter. These numbers are for the 3/4" Scorpion bars.

The Stinger has a minimum opening of about a 5/8" minimum diameter. Depth is about 8" for the Stinger. Numbers vary depending upon vessel design and the turners skill level.

The turners who have used these tools will have additional feedback for you and I too look forward to reading their comments, input, and suggestions.

Be Well,

Don Pencil

WWW.DONPENCIL.COM

Manufacturer of the Scorpion and Stinger Hollow Vessel Boring Bar Systems.

Re: Scorpion

#4

Re: Scorpion

John Lucas

>Don I have my own hollowing tools that are built similar to yours. I find your depths to be right on. With the 3/4" bar I do start to get chatter beyond 10" but can go to 12 or 14 without a lot of hassle. Beyond that the chatter gets pretty rough.

On the smaller bars 6 to 8" is about right also but depends on the cutter I use.

Re: Scorpion

#5

Elbow pain..

W.C. Turner

>For someone with artharitis elbows, hands, etc., wouldn't it be better to have a captured type system? I'm afraid the armbrace type would further aggravate my condition?

Thanks for any replies.

W.C.

Re: Scorpion

#6

Tell me..

W.C. Turner

>Is the scorpion pretty hard on the elbows & hands?

Re: Scorpion

#7

Don Pencil

Re: Elbow pain..

Don Pencil

>Actually just the opposite.

Trying to hang on to a round tool is much more wearing on the joints and muscles.

A captured sysmtem is easier on the body but has its limits especially in terms of versitility. It's a give and take world.

Many tools can be used in the Scorpion handle system. It can be used both as a pistle grip or pistle grip with forearm support. Therefore a wide variety of tools can be used in the handle.

As a result, many who suffer from arthitis and other problems find that they can use their tools much more easily than with a round handle. The pistle grip is a whole lot easier to handle and takes much less gripping power that a round handle.

Be Well,

Don

Re: Scorpion

#8

Re: Elbow pain..

George Van in WI

>Thanks for the tip Don. I like your product. I never thought to use the pistol grip feature and find some pieces awkward to hollow with the arm brace attached do to body position. This may help.

Re: Scorpion

#9

Re: Scorpion

Guy

>Hello, I've gone about 10 inches deep with the Scorpion and a couple inches with the Stinger. Could have gone more I guess but but wasn't going for max just turning. These tools weren't flexing, bouncing around. Bought these a few years ago from Don at the Indy show (same one that Stuart Mortimer was demo'ing at). They have held up very well, still look and feel new. Have seen and played with the John Jordan's, Sorby's, etc, etc and I don't feel I am missing a thing. The quality of these tools even years later remains apparent even in my bumbling hands. So for what it's worth I haven't looked for another hollowing system since I have picked these up.

Re: Scorpion

#10

I bought my scorpion set at that same show.

Al Crandall (NE of Indy)

>