Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Exotic Hardwood, Personally Sourced Worldwide. Inspected at Origin. Shop Rare Stock.

Questions for segmented turners

Posts

Questions for segmented turners

#1

Questions for segmented turners

Barry Irby

>I know, its the turnings that are segmented, not the turners.

I have a couple of left over boards of Australian Cypress flooring. I turned some plugs today to patch holes in the floor. Not completely sure it is really Australian or Cypress, but it smells great and turns like butter. I was thinking of cutting it up and making a segmented bowl out of it. Now for the questions,

If I glue up multi-sided rings, how do I flatten them, so I can glue them in a stack to make the bowl? I have a Performax. Can I just run them through, or do I need a sled?

What kind of glue do I use?

Without getting too complicated, whats the best?easiest way to cut the segments. And while you are at it, how high is UP? I am not thinking of a fancy pattern, just a bowl.

Re: Questions for segmented turners

#2

Bob Moffett

Re: Questions for segmented turners

Bob Moffett

>Barry,

Try going to Kevin Neelley's website, Turnedwood.com and I think you will find the all the answers to your questions there. A Proformax is great for flattening the rings. I run them through mine 4 times, turning the ring 90 degrees each time to compensate for the chance that everything on the Proformax is not set up perfectly square. Let us see how your bowl turns out.

Happy Turning,

Bob

Re: Questions for segmented turners

#3

Re: Questions for segmented turners

Ad de Crom Netherlands

>Hi Barry.

I do a lot of segmemted turnings.

My way to do that is not the easyest way, I developed my own style.

I use always a faceplate.

The numbers of segmented ring depend on what you have in your mind.

Time is not important for me, time enough since my retirement.

I use always 12 segments per ring.

For gueing I use Bison super wood glue.

Started with a base ring on the faceplate and flatten that base ring.

I flatten one side of the next segmented ring on a flat board covered with sandpaper, so also very easy, so also handwork.

The next stap is to glue the next ring and let it dry for a whole day.

The next stap is flatten the second glued rimg on the lathe till I reach the right height of that segmented ring.

Than repeat this with the third ring and so on till the last segmented ring.

I know there are many ways to do this, and probably better ways, but I like it to be sure I have the right height of every segmented ring according my design. My way of working is time consuming.

Now I prepaired a drawing of a pine segmented translucent lamp shade for my next project ( see picture)

Maybe this is a little help for you.

As you know a woodturner have to be very patient, at least in my opinion for the best result.


img

Re: Questions for segmented turners

#4

Re: Questions for segmented turners

Dennis Daudelin

>Barry,

Using the Performax is fine. Just sand them until the glue remains are removed. I try and glue all my rings at the same time so that when I do sand, I sand all the rings the same height (meaning they all go through the sander each time I reduce the height.

You don't need a sled when sanding on the Performax.

As far as glue, Titebond II will work fine. I use Titebond II for gluing my segments into rings. ButI prefer to use a veneer glue (Unibond) for gluing the rings into stacks as I don't later get the glue creep between the rings.

As far as height of the bowl, well that's mainly up to how wide is the bowl and at what angle are you planning for the sides of the bowl. The proportions should be no different than a solid wood bowl where the foot is best at ~33% of the rim size.

If you're interested (or anyone else), I've written a beginner's segmented bowl document (23 pages) that explains the complete process to making your first bowl. I use this a lot for doing classes.

I hope that this helps,

Dennis

Re: Questions for segmented turners

#5

Re: Questions for segmented turners

albertabob

>Hi Barry;

I new to this stuff too but I got thought one last week.

I wa hapy I made this press to flatten the rings as they can get out of line fas reducing the thickness after you sand them.

The screw was available at Lee Valley( google it)

I dadoed the bas so I could remove it for storage.

The frame is scrap. Use a decent channel if you have to buy some.

p.s. now it's cheaper than wood!

I also found that there are differnt type of pipe straps so make usre the one you get dont interfere with the ring lying flat.

Regards

Bob


img

Re: Questions for segmented turners

#6

Re: Questions for segmented turners *LINK*

georgetroy

>So many pieces so little time. Listing my segmented website which give basic instructions and drawings. Start with something small like a cereal bowl. GT


George Troy Segmented Woodturner