Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

If you sell to woodworkers, your customers are already here

Spalted Maple Hollowform

Posts

Spalted Maple Hollowform

#1

Spalted Maple Hollowform

David Propst

>This 8 x 4.5� hollow form is from a spalted maple crotch piece. It was originally going to have an ebony collar, but I decided the simpler form would be less distracting and allow the nice top figure to be shown to greatest advantage. The form is more squat than I prefer, but again I was trying to show off what I thought was a spectacular piece of wood.

My hollow forms are becoming lighter (thinner) and this is the lightest for the size I have yet turned. The walls are approximately �". It was fun to show it to my wife and then hand it to her and see her expression when she felt how light it was. I have a small hollow form of Wally�s that I keep near for inspiration and the lightness has been commented on by everyone I have shown it too.

The piece was sanded to 400 grit, Deft was applied a couple of times and wiped off to seal the wood, next two coats of Velvit Oil were wet sanded on with 400 grit, and then two coats of Tru-Oil. Before, between and after Tru-Oil oil coats it was buffed with Abralon 500-2000.

Please offer your critiques. My turning exchange recipient won�t mind! :-)

Best Regards,

David


img

Re: Spalted Maple Hollowform

#2

Profile view of Maple Hollowform 

David Propst

>


img

Re: Spalted Maple Hollowform

#3

It's a beauty...............

Jennifer@Indy.USA

>David here's my critique : Wicked Good!

I love the form....I love the way it lifts off the table and the very slight lift at the opening brings everything together. You're right....it is a spectacular piece of wood. I love spalted pieces with deep dark spalting. It makes such a dramatic contrast. With this piece you not only get that...but the awesome figure of the crotch wood moving around under that. It truly is a fabulous piece! If this is yur exchange piece....somebody is going to be mighty delighted! Excelent work my friend :) You know you're feeling good!!!

Jennifer

Re: Spalted Maple Hollowform

#4

Re: Spalted Maple Hollowform

tek-Brunswick, Ohio

>I think that you made a wise choice leaving the collar off. Visually there is a lot going on because of the grain and the spalting. I think wood with that much character is better in the simple clean forms like the one you have made. I think texturing and other embellishments usually are better on plainer woods. Just my 2 cents worth from someone who has not done a hollow form larger than Christmas Ornaments yet. Nice job!

Re: Spalted Maple Hollowform

#5

Brad Vietje

Re: Spalted Maple Hollowform

Brad Vietje

>Beautiful work, David -- I agree that a collar would detract. It's excellent the way it is !

Safe Spinning,

Brad Vietje

Newbury, VT

Re: Spalted Maple Hollowform

#6

Re: Spalted Maple Hollowform

Bill MacLachlan

>David; A beautiful piece of work. I am amazed how you get it 1/4" thick through the small neck. I agree it does not need the collar as the wood has more than enough character as is. Well done.

Bill

Re: Spalted Maple Hollowform

#7

Re: Spalted Maple Hollowform

Jim Shaver - Oakville, Ontario

>Hi David,

Beautiful wood Beautifully done, your forms are always wonderful.

Take care,

Jim

Re: Spalted Maple Hollowform

#8

Nice!

Barry Turner

>Nice! I like the figure of the wood and the spalting. Either would have produced a striking piece.......you got both.

Barry

Re: Spalted Maple Hollowform

#9

Wowser!

Molly Winton

>How can you critique perfection? I love the very slight lift of the opening. It's very subtle and graceful. I can see why you wanted to show off the spalting. It's very spectacular. Beautiful David. I'm hoping your email to me earlier was a cryptic way of letting me know THIS IS MINE!! My fingers are crossed, which will be very inconvenient for the next few days.

Re: Spalted Maple Hollowform

#10

Re: Wowser!

Mac

>Geeezum Molly, I was hoping it was headed east towards me...........

Re: Spalted Maple Hollowform

#11

Re: Spalted Maple Hollowform

Terry Quiram, Roanoke Illinois

>Wow David

Spectacular spalting. The shape is terrific and I am glad you left the collar off.

Terry

Re: Spalted Maple Hollowform

#12

Beautiful Spalting!

Gerry Meekins in Maryland

>Great job David,

I�ll bet you it was exciting turning this one. You never know what you will be getting yourself into with a piece this spalted. Love the lift around the opening too. Just enough.

Thanks for posting the pictures of this piece!

Gerry

Re: Spalted Maple Hollowform

#13

Re: Beautiful Spalting!

Ed Karch

>In design there is another rule of three that is not as widely known. More than three major features is a distraction. You have the beautiful form, great spalting, and crotch figure. You are right on the money a collar would be too much.

Re: Spalted Maple Hollowform

#14

Re: Profile view of Maple Hollowform

Sam Dean

>That really is a fantastic piece! I honestly can't think of anything that would considerably help the design. Tons of things could be done to make it look different, but it's just spectacular the way it is.

Thanks,

Sam

Re: Spalted Maple Hollowform

#15

Re: Spalted Maple Hollowform

George Van in WI

>It's all been said Dave but I gotta say it's great!

Re: Spalted Maple Hollowform

#16

Re: Profile view of Maple Hollowform

Carole Valentine

>Wonderful form for a spectacular piece of wood David. I think you did the right thing by omitting the collar and just leaving the tiniest upsweep instead.